- 您現在的位置：買賣IC網 > PDF目錄19912 > EPCS4SI8N (Altera)IC CONFIG DEVICE 4MBIT 8-SOIC PDF資料下載
參數資料
| 型號： | EPCS4SI8N |
| 廠商： | Altera |
| 文件頁數： | 30/40頁 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 4MBIT 8-SOIC |
| 產品培訓模塊： | Three Reasons to Use FPGA's in Industrial Designs |
| 標準包裝： | 100 |
| 系列： | EPCS |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 4Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 604 (CN2011-ZH PDF) |
| 其它名稱： | 544-1379-5 EPCS4SI8N-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Page 36
Pin Information
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Table 23 lists the pin description of the EPCS device.
Figure 23 shows the layout recommendation for vertical migration from the EPCS1
device to the EPCS128 device.
Table 23. EPCS Device Pin Description
Pin
Name
Pin Number
in 8-Pin
SOIC
Package
Pin Number
in 16-Pin
SOIC
Package
Pin Type
Description
DATA
2
8
Output
The DATA output signal transfers data serially out of the EPCS device
to the FPGA during the read operation or configuration. During the
read operation or configuration, the EPCS device is enabled by pulling
the nCS signal low. The DATA signal transitions on the falling edge of
the DCLK signal.
ASDI
5
15
Input
The ASDI signal is used to transfer data serially into the EPCS device.
This pin are also receiving data that are programmed into the EPCS
device. Data is latched on the rising edge of the DCLK signal.
nCS
1
7
Input
The nCS signal toggles at the beginning and the end of a valid
instruction. When this signal goes high, the device is deselected and
the DATA pin is tri-stated. When this signal goes low, the device is
enabled and in an active mode. After power up, the EPCS device
requires a falling edge on the nCS signal before the EPCS device
begins any operation.
DCLK
6
16
Input
The FPGA provides the DCLK signal. This signal provides the timing
for the serial interface. The data presented on the ASDI pin is latched
to the EPCS device on the rising edge of the DCLK signal. The data on
the DATA pin changes after the falling edge of the DCLK signal and is
latched into the FPGA on the next falling edge of the DCLK signal.
VCC
3, 7, 8
1, 2, 9
Power
Connect the power pins to a 3.3-V power supply.
GND
4
10
GND
Ground pin.
Figure 23. Layout Recommendation for Vertical Migration from the EPCS1 Device to the EPCS128
Device
Pi
n1
ID
Pin 1 ID
相關PDF資料 |
PDF描述 |
|---|---|
| GRM2165C2A111JA01D | CAP CER 110PF 100V 5% NP0 0805 |
| RCB92DHRR-S330 | EDGECARD EXT PCI 184PS .050 3.3V |
| FMC18DREH | CONN EDGECARD 36POS .100 EYELET |
| 1250L4 | BATTERY PK S-HD 6.0V D SIZE ZINC |
| EPC1PC8 | IC CONFIG DEVICE 1MBIT 8-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPCS4SI8N | 制造商:Altera Corporation 功能描述:SEMICONDUCTOR ((NW)) |
| EPCS64 | 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Serial Configuration Devices |
| EPCS64SI16N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Mb 40 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPCSC2.5T | 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
| EPCSC2.5T1-2 | 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
發布緊急采購，3分鐘左右您將得到回復。