- 您現在的位置：買賣IC網 > PDF目錄384277 > EDD2508AETA (Elpida Memory, Inc.) 256M bits DDR SDRAM PDF資料下載
參數資料
| 型號： | EDD2508AETA |
| 廠商： | Elpida Memory, Inc. |
| 英文描述： | 256M bits DDR SDRAM |
| 中文描述： | 256M比特DDR內存 |
| 文件頁數： | 10/52頁 |
| 文件大小： | 492K |
| 代理商： | EDD2508AETA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
EDD2508AETA, EDD2516AETA
Data Sheet E0859E50 (Ver. 5.0)
10
-6B
-7A
-7B
Parameter
Symbol
min.
max.
min.
max
min.
max.
Unit Notes
Write recovery time
tWR
15
—
15
—
15
—
ns
Auto precharge write recovery and
precharge time
Internal write to Read command
delay
tDAL
(tWR/tCK)+
(tRP/tCK)
(tWR/tCK)+
(tRP/tCK)
—
(tWR/tCK)+
(tRP/tCK)
—
tCK 13
tWTR
1
—
1
—
1
—
tCK
Average periodic refresh interval
tREF
—
7.8
—
7.8
—
7.8
μs
Notes: 1. On all AC measurements, we assume the test conditions shown in the next page. For timing parameter
definitions, see ‘Timing Waveforms’ section.
2. This parameter defines the signal transition delay from the cross point of CK and /CK. The signal
transition is defined to occur when the signal level crossing VTT.
3. The timing reference level is VTT.
4. Output valid window is defined to be the period between two successive transition of data out or DQS
(read) signals. The signal transition is defined to occur when the signal level crossing VTT.
5. tHZ is defined as DOUT transition delay from Low-Z to High-Z at the end of read burst operation. The
timing reference is cross point of CK and /CK. This parameter is not referred to a specific DOUT voltage
level, but specify when the device output stops driving.
6. tLZ is defined as DOUT transition delay from High-Z to Low-Z at the beginning of read operation. This
parameter is not referred to a specific DOUT voltage level, but specify when the device output begins
driving.
7. Input valid windows is defined to be the period between two successive transition of data input or DQS
(write) signals. The signal transition is defined to occur when the signal level crossing VREF.
8. The timing reference level is VREF.
9. The transition from Low-Z to High-Z is defined to occur when the device output stops driving. A specific
reference voltage to judge this transition is not given.
10. tCK (max.) is determined by the lock range of the DLL. Beyond this lock range, the DLL operation is not
assured.
11. tCK = tCK (min) when these parameters are measured. Otherwise, absolute minimum values of these
values are 10% of tCK.
12. VDD is assumed to be 2.6V ± 0.1V (DDR400), 2.5V ± 0.2V (DDR333, 266). VDD power supply variation
per cycle expected to be less than 0.4V/400 cycle.
13. tDAL = (tWR/tCK)+(tRP/tCK)
For each of the terms above, if not already an integer, round to the next highest integer.
Example: For –5C Speed at CL = 3, tCK = 5ns, tWR = 15ns and tRP= 18ns,
tDAL = (15ns/5ns) + (18ns/5ns) = (3) + (4)
tDAL = 7 clocks
相關PDF資料 |
PDF描述 |
|---|---|
| EDD2508AETA-5B-E | 256M bits DDR SDRAM |
| EDD2508AETA-5C-E | 256M bits DDR SDRAM |
| EDD2508AETA-6B-E | 256M bits DDR SDRAM |
| EDD2508AETA-7A-E | 256M bits DDR SDRAM |
| EDD2508AETA-7B-E | 256M bits DDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EDD2508AETA-5B-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M bits DDR SDRAM |
| EDD2508AETA-5C-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M bits DDR SDRAM |
| EDD2508AETA-6B-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M bits DDR SDRAM |
| EDD2508AETA-7A-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M bits DDR SDRAM |
| EDD2508AETA-7B-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M bits DDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。