- 您現在的位置：買賣IC網 > PDF目錄377000 > DSP56364P (飛思卡爾半導體(中國)有限公司) 24-Bit Audio Digital Signal Processor PDF資料下載
參數資料
| 型號： | DSP56364P |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 數字信號處理 |
| 英文描述： | 24-Bit Audio Digital Signal Processor |
| 中文描述： | 24位音頻數字信號處理器 |
| 文件頁數： | 11/148頁 |
| 文件大?。?/td> | 1204K |
| 代理商： | DSP56364P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
Serial Host Interface
DSP56364 Technical Data, Rev. 4
Freescale Semiconductor
2-7
2.7
The SHI has five I/O signals that can be configured to allow the SHI to operate in either SPI or I
2
C mode.
Serial Host Interface
Table 2-9 Serial Host Interface Signals
Signal
Name
Signal
Type
State during
Reset
Signal Description
SCK
Input or
output
Tri-stated
SPI Serial Clock
—The SCK signal is an output when the SPI is configured as a master
and a Schmitt-trigger input when the SPI is configured as a slave. When the SPI is
configured as a master, the SCK signal is derived from the internal SHI clock generator.
When the SPI is configured as a slave, the SCK signal is an input, and the clock signal
from the external master synchronizes the data transfer. The SCK signal is ignored by
the SPI if it is defined as a slave and the slave select (SS) signal is not asserted. In both
the master and slave SPI devices, data is shifted on one edge of the SCK signal and is
sampled on the opposite edge where data is stable. Edge polarity is determined by the
SPI transfer protocol.
SCL
Input or
output
Tri-stated
I
2
C Serial Clock
—SCL carries the clock for I
2
C bus transactions in the I
2
C mode. SCL
is a Schmitt-trigger input when configured as a slave and an open-drain output when
configured as a master. SCL should be connected to V
CC
through a pull-up resistor.
This signal is tri-stated during hardware, software, and individual reset. Thus, there is
no need for an external pull-up in this state.
This input is 5 V tolerant.
MISO
Input or
output
Tri-stated
SPI Master-In-Slave-Out
—When the SPI is configured as a master, MISO is the
master data input line. The MISO signal is used in conjunction with the MOSI signal for
transmitting and receiving serial data. This signal is a Schmitt-trigger input when
configured for the SPI Master mode, an output when configured for the SPI Slave
mode, and tri-stated if configured for the SPI Slave mode when SS is deasserted. An
external pull-up resistor is not required for SPI operation.
SDA
Input or
open-drain
output
Tri-stated
I
2
C Data and Acknowledge
—In I
2
C mode, SDA is a Schmitt-trigger input when
receiving and an open-drain output when transmitting. SDA should be connected to
V
CC
through a pull-up resistor. SDA carries the data for I
2
C transactions. The data in
SDA must be stable during the high period of SCL. The data in SDA is only allowed to
change when SCL is low. When the bus is free, SDA is high. The SDA line is only
allowed to change during the time SCL is high in the case of start and stop events. A
high-to-low transition of the SDA line while SCL is high is a unique situation, and is
defined as the start event. A low-to-high transition of SDA while SCL is high is a unique
situation defined as the stop event.
This signal is tri-stated during hardware, software, and individual reset. Thus, there is
no need for an external pull-up in this state.
This input is 5 V tolerant.
MOSI
Input or
output
Tri-stated
SPI Master-Out-Slave-In
—When the SPI is configured as a master, MOSI is the
master data output line. The MOSI signal is used in conjunction with the MISO signal
for transmitting and receiving serial data. MOSI is the slave data input line when the
SPI is configured as a slave. This signal is a Schmitt-trigger input when configured for
the SPI Slave mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DSP56366P | 24-Bit Audio Digital Signal Processor |
| DSP56366UM | 24-Bit Audio Digital Signal Processor |
| DSP56367P | 24-Bit Audio Digital Signal Processor |
| DSP56367UM | 24-Bit Audio Digital Signal Processor |
| DSP56600 | Implementing Viterbi Decoders Using the VSL Instruction on DSP Families |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP56364UM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56364 24-Bit Digital Signal Processor User＇s Manual |
| DSP56366 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56366 24-Bit Audio Digital Signal Processor |
| DSP56366P | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:24-Bit Audio Digital Signal Processor |
| DSP56366UM | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:24-Bit Audio Digital Signal Processor |
| DSP56367 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。