- 您現在的位置：買賣IC網 > PDF目錄17023 > DS4830EVKIT# (Maxim Integrated Products)EVAL KIT OPTICAL MICROCONTROLLER PDF資料下載
參數資料
| 型號： | DS4830EVKIT# |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT OPTICAL MICROCONTROLLER |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
DS4830
Optical Microcontroller
19
Maxim Integrated
Figure 6. Memory Map When Program is Executing from Flash Memory
Internalself-testroutines
Callableroutinesforin-applicationflashprogramming
Following any reset, execution begins in the utility ROM.
The ROM software determines whether the program
execution should immediately jump to location 0000h,
the start of application code, or to one of the special
routines mentioned. Routines within the utility ROM are
firmware-accessible and can be called as subroutines by
the application software. More information on the utility
ROM contents is contained in the DS4830 User’s Guide.
Password
Some applications require protection against unau-
thorized viewing of program code memory. For these
applications, access to in-system programming, in-appli-
cation programming, or in-circuit debugging functions
is prohibited until a password has been supplied. The
password is defined as the 16 words of physical program
memory at addresses 0010h–001Fh.
A single password lock (PWL) bit is implemented in
the device. When the PWL is set to 1 (power-on-reset
default) and the contents of the memory at addresses
0010h–001Fh are any value other than all FFh or 00h, the
password is required to access the utility ROM, includ-
ing in-circuit debug and in-system programming routines
that allow reading or writing of internal memory. When
PWL is cleared to 0, these utilities are fully accessible
without the password. The password is automatically set
to all ones following a mass erase.
Detailed information regarding the password can be
found in the DS4830 User’s Guide.
SYSTEM
REGISTERS
PERIPHERAL
REGISTERS
DP
16 x 16
STACK
M5
M4
M3
M2
M1
M0
5h
0Fh
00h
4h
3h
2h
1h
0h
FFFFh
8FFFh
9FFFh
8FFFh
7FFFh
0000h
4K x 16
UTILITY ROM
8K x 8
UTILITY ROM
4K x 16
UTILITY ROM
2K x 8
SRAM DATA
1K x 16
SRAM DATA
32K x 16
USER PROGRAM
MEMORY
8000h
07FFh
03FFh
DPC
SP
IP
PFX
A
AP
Fh
00h
0Fh
00h
1Fh
Eh
Dh
Ch
Bh
9h
8h
PROGRAM
MEMORY SPACE
DATA MEMORY
(BYTE MODE)
DATA MEMORY
(WORD MODE)
001Fh
0010h
PASSWORD
相關PDF資料 |
PDF描述 |
|---|---|
| GCM30DCSD | CONN EDGECARD 60POS DIP .156 SLD |
| GCM30DCMN | CONN EDGECARD 60POS .156 WW |
| GCM30DCMH | CONN EDGECARD 60POS .156 WW |
| GCM30DCMD | CONN EDGECARD 60POS .156 WW |
| GCM24DCCS | CONN EDGECARD 48POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4830EVKIT# | 功能描述:開發板和工具包 - 其他處理器 DS4830 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| DS4830RD# | 功能描述:開發板和工具包 - 其他處理器 REFERENCE DESIGN FOR DS4830/DS3923 RoHS:否 制造商:Maxim Integrated 產品: 工具用于評估: 核心: 接口類型: 工作電源電壓: |
| DS4830T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Optical Microcontroller 16-Bit MAXQ20 Low-Power Microcontroller |
| DS4830T+ | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| DS4830T+T | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。