參數資料
型號： DS26303LN-75+
廠商： Maxim Integrated Products
文件頁數： 11/101頁
文件大?。?/td> 0K
描述： IC LIU E1/T1/J1 3.3V 144-ELQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 13
類型： 線路接口裝置（LIU）
驅動器/接收器數： 8/8
規程： T1/E1/J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP 裸露焊盤
供應商設備封裝： 144-LQFP 裸露焊盤
包裝： 托盤
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
17 of 101
NAME
PIN
TYPE
FUNCTION
A4/RIMPMSB
12
A3/GMC3
13
A2/GMC2
14
A1/GMC1
15
A0/GMC0
16
I
Address Bus 4–0/G.772 Monitoring Control/Rx Impedance
Mode Select
A[4:0]:
These five pins are address pins in parallel host mode. In
serial host mode and multiplexed host mode, these pins should be
grounded.
RIMPMSB:
In hardware mode when this pin is low, the internal
impedance mode is selected, so all RTIP and RING pins require
no external resistance component. When high, external
impedance mode is selected so all RTIP and RING pins require
external resistance.
GMC[3:0]:
In hardware mode, these signal pins are used to select
a transmit line (TTIPn/TRINGn) or receive line (RTIPn/RRINGn)
for nonintrusive monitoring. Receiver 1 is used to monitor
channels 2 to 8 See Table 5-9.
OE
114
I
Output Enable.
If this pin is pulled low, all the transmitter outputs
(TTIPn and TRINGn) are high impedance. Additionally, the user
may use this same pin to turn off all the impedance matching for
the receivers at the same time if register bit GMR.RHPMC is set.
CLKE
115
I
Clock Edge.
When CLKE is high, SDO is valid on the falling edge
of SCLK. When CLKE is low SDO is valid on the rising edge of
SCLK. When CLKE is high, the RCLKn for all the channels is
inverted. This aligns RPOSn/RNEGn on the falling edge of RCLKn
and overrides the settings in register RCLKI. When low,
RPOSn/RNEGn is aligned according to the settings in register
JTAG
JTRSTB
95
I, pullup
JTAG Test Port Reset.
This pin if low resets the JTAG port. If not
used it can be left floating.
JTMS
96
I, pullup
JTAG Test Mode Select.
This pin is clocked on the rising edge of
JTCLK and is used to control the JTAG selection between scan
and test machine control.
JTCLK
97
I
JTAG Test Clock.
The data JTDI and JTMS are clocked on rising
edge of JTCLK and JTDO is clocked out on the falling edge of
JTCLK.
JTDO
98
O,
high-Z
JTAG Test Data Out.
This is the serial output of the JTAG port.
The data is clocked out on the falling edge of JTCLK.
JTDI
99
I, pullup
Test Data Input.
This pin input is the serial data of the JTAG test.
The data on JTDI is clocked on the rising edge of JTCLK. This pin
can be left unconnected.
相關PDF資料
PDF描述
DS3151+ IC LIU DS3/E3/STS-1 SGL 144CSBGA
VE-26X-IU-F2 CONVERTER MOD DC/DC 5.2V 200W
MC100EP17DTR2G IC RCVR/DRV ECL QUAD DFF 20TSSOP
DS2181AQ+T&R IC TXRX CEPT PRIMARY RATE 44PLCC
MS27468T11B98PB CONN RCPT 6POS JAM NUT W/PINS
相關代理商/技術參數
參數描述
DS26303LN-75+ 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
DS26303LN-75+A3 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
DS26303LN-75A3 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
DS26303LN-XXX 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit
DS26303LN-XXX+ 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*