參數資料
型號: DS2423X
廠商: DALLAS SEMICONDUCTOR
元件分類: Memory IC:Other
英文描述: SPECIALTY MEMORY CIRCUIT, UUC
封裝: CHIP SCALE PKG
文件頁數: 14/25頁
文件大小: 579K
代理商: DS2423X
DS2422/DS2423
21 of 25
CRC GENERATION
With the DS242X there are two different types of CRCs (Cyclic Redundancy Checks). One CRC is an 8-
bit type and is stored in the most significant byte of the 64-bit ROM. The bus master can compute a CRC
value from the first 56 bits of the 64-bit ROM and compare it to the value stored within the DS242X to
determine if the ROM data has been received error-free by the bus master. The equivalent polynomial
function of this CRC is: X
8 + X5 + X4 + 1. This 8-bit CRC is received in the true (non-inverted) form
when reading the ROM of the DS242X. It is computed at the factory and lasered into the ROM.
The other CRC is a 16-bit type, generated according to the standardized CRC16-polynomial function x
16
+ x
15 + x2 + 1. This CRC is used for error detection when reading Data Memory using the Read Memory
+ Counter command and for fast verification of a data transfer when writing to the scratchpad. It is the
same type of CRC as is used with NV RAM based iButtons for error detection within the iButton
Extended File Structure. In contrast to the 8-bit CRC, the 16-bit CRC is always returned or sent in the
complemented (inverted) form. A CRC-generator inside the DS242X chip (Figure 12) will calculate a
new 16-bit CRC as shown in the command flow chart of Figure 7. The bus master compares the CRC
value read from the device to the one it calculates from the data and decides whether to continue with an
operation or re-read the portion of the data with the CRC error.
With the initial pass through the Read Memory + Counter flow chart the 16-bit CRC value is the result of
shifting the command byte into the cleared CRC generator, followed by the 2 address bytes, data bytes,
value of the counter associated with the page and zero bits. Subsequent passes through the Read Memory
+ Counter flow chart will generate a 16-bit CRC that is the result of clearing the CRC generator and then
shifting in the data bytes, the value of the counter and the zero bits.
With the Write Scratchpad command the CRC is generated by first clearing the CRC generator and then
shifting in the command code, the Target Addresses TA1 and TA2 and all the data bytes. The DS242X
will transmit this CRC only if the data bytes written to the scratchpad include scratchpad ending offset
11111b. The data may start at any location within the scratchpad.
For more details on generating CRC values including example implementations in both hardware and
software, see the Book of DS19xx iButton Standards.
相關PDF資料
PDF描述
DS2423 4K X 1 STANDARD SRAM, PDSO6
DS2422 1K X 1 STANDARD SRAM, PDSO6
DS2430AP 256 X 1 1-WIRE SERIAL EEPROM, PDSO6
DS2430A 32 X 8 1-WIRE SERIAL EEPROM, PBCY3
DS2430AX 32 X 8 1-WIRE SERIAL EEPROM, UUC2
相關代理商/技術參數
參數描述
DS243 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
DS2430 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM
DS2430A 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
DS2430A R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM
DS2430A T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM