- 您現在的位置：買賣IC網 > PDF目錄376952 > DS2415V 1-Wire Time Chip PDF資料下載
參數資料
| 型號： | DS2415V |
| 英文描述： | 1-Wire Time Chip |
| 中文描述： | 1 - Wire時鐘芯片 |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 142K |
| 代理商： | DS2415V |
DS1385/DS1387
012496 2/20
PIN DESCRIPTION
OER
X1
X2
AD0-AD7
CS
ALE
WR
RD
WER
IRQ
drain)
AS1
AS0
SQW
V
CC
GND
V
BAT
BGND
NC
– RAM Output Enable
– Crystal Input
– Crystal Output
– Mux’ed Address/Data Bus
– RTC Chip Select Input
– RTC Address Strobe
– RTC Write Data Strobe
– RTC Read Data Strobe
– RAM Write Data Strobe
– Interrupt Request Output (open
– RAM Upper Address Strobe
– RAM Lower Address Strobe
– Square Wave Output
– +5V Supply
– Ground
– Battery + Supply
– Battery Ground
– No Connection
DESCRIPTION
The DS1385/DS1387 RAMified Real Time Clocks
(RTCs) are upward–compatible successors to the in-
dustry standard DS1285/DS1287 RTC’s for PC applica-
tions. In addition to the basic DS1285/DS1287 RTC
functions, 4K bytes of on–chip nonvolatile RAM have
been added.
The RTC functions include a time–of–day clock, a one-
hundred year calendar, time–of–day interrupt, periodic
interrupts, and an end–of–clock update cycle interrupt.
In addition, 50–bytes of user NV RAM are provided with-
in this basic RTC function which can be used to store
configuration data. The clock and user RAM are main-
tained in the absence of system V
CC
by a lithium battery.
The 4K x 8 additional NV RAM is provided to store a
much larger amount of system configuration data than is
possible within the original 50–byte area. This RAM is
accessed via control signals separate from the RTC,
and is also maintained as nonvolatile storage from the
lithium battery.
OPERATION
The block diagram in Figure 1 shows the pin connec-
tions with the major internal functions of the
DS1385/DS1387. The following paragraphs describe
the function of each pin.
SIGNAL DESCRIPTIONS
GND, V
CC
–
DC power is provided to the device on
these pins. V
CC
is the +5 volt input. When 5 volts are
applied within normal limits, the device is fully accessi-
ble and data can be written and read. When V
CC
is be-
low 4.25 volts typical, reads and writes are inhibited.
However, the timekeeping function continues unaf-
fected by the lower input voltage. As V
CC
falls below 3
volts typical, the RAM and timekeeper are switched
over to the energy source connected to the V
BAT
pin in
the case of the DS1385, or to the internal battery in the
case of the DS1387. The timekeeping function main-
tains an accuracy of
±
1 minute per month at 25
°
C re-
gardless of the voltage input on the V
CC
pin.
SQW (Square Wave Output)
–
The SQW pin can output
a signal from one of 13 taps provided by the 15 internal
divider stages of the real time clock. The frequency of the
SQW pin can be changed by programming Register A as
shown in Table 2. The SQW signal can be turned on and
off using the SQWE bit in Register B. The SQW signal is
not available when V
CC
is less than 4.25 volts typical.
AD0–AD7 (Multiplexed Bi–directional Address/Data
Bus)
–
Multiplexed buses save pins because address
information and data information time share the same
signal paths. The addresses are present during the first
portion of the bus cycle and the same pins and signal
paths are used for data in the second portion of the
cycle. Address/data multiplexing does not slow the ac-
cess time of the DS1385/DS1387 since the bus change
from address to data occurs during the internal RAM ac-
cess time. Addresses must be valid prior to the latter
portion of ALE, AS0, or AS1, at which time the
DS1385/DS1387 latches the address from AD0 to AD7.
Valid write data must be present and held stable during
the latter portion of the WR or WER pulses. In a read
cycle, the DS1385/DS1387 outputs eight bits of data
during the latter portion of the RD or OER pulses. The
read cycle is terminated and the bus returns to a high im-
pedance state as RD or OER transitions high.
ALE (RTC Address Strobe Input)
–
A positive going
address strobe pulse serves to demultiplex the bus.
The falling edge of ALE causes the RTC address to be
latched within the DS1385/DS1387.
RD (RTC Read Input) –
RD identifies the time period
when the DS1385/DS1387 drives the bus with RTC
read data. The RD signal is an enable signal for the out-
put buffers of the clock.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2415X | 1-Wire Time Chip |
| DS1395 | RAMified Real Time Clock |
| DS1395S | RAMified Real Time Clock |
| DS1402D-41 | iButton Probe Component Parts |
| DS1402 | iButton Probe Component Parts |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2415X | 功能描述:IC TIME CHIP 1-WIRE CSP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| DS2416FP00K | 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,416,3P208V,CC |
| DS2416FR000 | 制造商:Thomas & Betts 功能描述:200A,REC,3P4W,MG,416,3P208V,SC |
| DS2416FRAB0 | 制造商:Thomas & Betts 功能描述:200A,REC.,3P4W,3PHASE,208V |
| DS2416MP000 | 制造商:Thomas & Betts 功能描述:DS2416MP000 200A,PLG,3P4W,MG,416 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,416,3P208V |
發布緊急采購，3分鐘左右您將得到回復。