參數資料
型號： DS2154LD2+
廠商： Maxim Integrated Products
文件頁數： 61/87頁
文件大?。?/td> 0K
描述： IC TXRX E1 5V 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
類型： 收發器
驅動器/接收器數： 1/1
規程： E1
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
DS2154
64 of 87
13.1 Receive Clock and Data Recovery
The DS2154 contains a digital clock recovery system. See Figure 1-1 and Figure 13-1 for more details.
The DS2154 couples to the receive E1 shielded twisted pair or coax via a 1:1 transformer. See Table 13-2
for transformer details. The 2.048MHz clock attached at the MCLK pin is internally multiplied by 16 via
an internal PLL and fed to the clock recovery system. The clock recovery system uses the clock from the
PLL circuit to form a 16 times oversampler, which is used to recover the clock and data. This
oversampling technique offers outstanding jitter tolerance (see Figure 13-2).
Normally, the clock that is output at the RCLKO pin is the recovered clock from the E1 AMI/B8ZS
waveform presented at the RTIP and RRING inputs. When no AMI signal is present at RTIP and RRING,
a Receive Carrier Loss (LRCL) condition will occur and the RCLKO will be sourced from the clock
applied at the MCLK pin. If the jitter attenuator is either placed in the transmit path or is disabled, the
RCLKO output can exhibit slightly shorter high cycles of the clock. This is due to the highly over-
sampled digital clock recovery circuitry. If the jitter attenuator is placed in the receive path (as is the case
in most applications), the jitter attenuator restores the RCLK to being close to 50% duty cycle. See the
Receive AC Timing Characteristics in Section 16 for more details.
13.2 Transmit Waveshaping and Line Driving
The DS2154 uses a set of laser-trimmed delay lines along with a precision Digital-to-Analog Converter
(DAC) to create the waveforms that are transmitted onto the E1 line. The waveforms created by the
DS2154 meet the ITU G.703 specifications. See Figure 13-3. The user will select which waveform is to
be generated by properly programming the L2/L1/L0 bits in the Line Interface Control Register (LICR).
The DS2154 can set up in a number of various configurations depending on the application. See
Table 13-1. Line Build-Out Select in LICR
LLL
210
APPLICATION
TRANSFORMER
RETURN
LOSS
(dB)
RT ()
000
75
normal (See Note 1)
1:1.15 step-up
N.M.
0
001
120
normal
1:1.15 step-up
N.M.
0
010
75
with protection resistors
1:1.15 step-up
N.M.
8.2
011
120
with protection resistors
1:1.15 step-up
N.M.
8.2
100
75
with high return loss
1:1.15 step-up
21
27
110
75
with high return loss
1:1.36 step-up
21
18
100
120
with high return loss
1:1.36 step-up
21
27
N.M. = not meaningful
Note: This LBO is not recommended for use in the DS2154 A2 revision.
Due to the nature of the design of the transmitter in the DS2154, very little jitter (less than 0.005UIP-P
broadband from 10Hz to 100kHz) is added to the jitter present on TCLKI. Also, the waveforms that they
create are independent of the duty cycle of TCLK. The transmitter in the DS2154 couples to the E1
transmit shielded twisted pair or coax via a 1:1.15 or 1:1.36 step-up transformer as shown in Figure 13-1.
For the devices to create the proper waveforms, this transformer used must meet the specifications listed
相關PDF資料
PDF描述
V375C24M150BG2 CONVERTER MOD DC/DC 24V 150W
VI-24M-MX-F4 CONVERTER MOD DC/DC 10V 75W
D38999/20WG11PB CONN RCPT 11POS WALL MNT W/PINS
MAX3480BEPI+ IC RS485/RS422 DATA INTRFC 28DIP
VI-24M-MX-F2 CONVERTER MOD DC/DC 10V 75W
相關代理商/技術參數
參數描述
DS2154LD2+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LN 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LN+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LNA2 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LNA2+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*