參數資料
型號： DS2152LN
英文描述： Enhanced T1 Single-Chip Transceiver
中文描述： 增強型T1單芯片收發器
文件頁數： 56/94頁
文件大?。?/td> 1003K
代理商： DS2152LN
DS2152
56 of 93
11.1.3 Basic Operation Details
To allow the DS2152 to properly source/receive data from/to the HDLC and BOC controller the legacy
FDL circuitry (which is described in Section 11.2) should be disabled and the following bits should be
programmed as shown:
TCR1.2 = 1 (source FDL data from the HDLC and BOC controller)
TBOC.6 = 1 (enable HDLC and BOC controller)
CCR2.5 = 0 (disable SLC-96 and D4 Fs-bit insertion)
CCR2.4 = 0 (disable legacy FDL 0 stuffer)
CCR2.1 = 0 (disable SLC-96 reception)
CCR2.0 = 0 (disable legacy FDL 0 stuffer)
IMR2.4 = 0 (disable legacy receive FDL buffer full interrupt)
IMR2.3 = 0 (disable legacy transmit FDL buffer empty interrupt)
IMR2.2 = 0 (disable legacy FDL match interrupt)
IMR2.1 = 0 (disable legacy FDL abort interrupt)
As a basic guideline for interpreting and sending both HDLC messages and BOC messages, the following
sequences can be applied:
Receive a HDLC Message or a BOC
1.
enable RBOC and RPS interrupts
2.
wait for interrupt to occur
3.
if RBOC=1, then follow steps 5 and 6
4.
if RPS=1, then follow steps 7 thru 12
5.
if LBD=1, a BOC is present, then read the code from the RBOC register and take action as needed
6.
if BD=0, a BOC has ceased, take action as needed and then return to step 1
7.
disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt
8.
read RPRM to obtain REMPTY status
a.
if REMPTY=0, then record OBYTE, CBYTE, and POK bits and then read the FIFO
a1. if CBYTE=0 then skip to step 9
a2. if CBYTE=1 then skip to step 11
b.
if REMPTY=1, then skip to step 10
9.
repeat step 8
10.
wait for interrupt, skip to step 8
11.
if POK=0, then discard whole packet, if POK=1, accept the packet
12.
disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to step 1
Transmit a HDLC Message
1.
make sure HDLC controller is finished sending any previous messages and is currently sending flags
by checking that the FIFO is empty by reading the TEMPTY status bit in the TPRM register
2.
enable either the THALF or TNF interrupt
3.
read TPRM to obtain TFULL status
a.
if TFULL=0, then write a byte into the FIFO and skip to next step (special case occurs when the
last byte is to be written, in this case set TEOM=1 before writing the byte and then skip to step 6)
b.
if TFULL=1, then skip to step 5
相關PDF資料
PDF描述
DS2152L Enhanced T1 Single-Chip Transceiver
DS2152 Enhanced T1 Single-Chip Transceiver
DS2160Q Data Encryption Processor
DS2160QN Peripheral IC
DS2165QL Solid-State Recorder
相關代理商/技術參數
參數描述
DS2152LN+ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2153DK 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
DS2153Q 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:E1 Single-Chip Transceiver
DS2153Q-A5 功能描述:IC TXRX E1 1-CHIP 5V 44-PLCC RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
DS2153Q-A5/T&R 制造商:Maxim Integrated Products 功能描述:IC TXRX E1 1-CHIP 5V 44-PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*