- 您現在的位置：買賣IC網 > PDF目錄9050 > DS1859E-050/T&R (Maxim Integrated Products)IC RES TEMP 50/50K 3MON 16-TSSOP PDF資料下載
參數資料
| 型號： | DS1859E-050/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 19/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RES TEMP 50/50K 3MON 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 50 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.85 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 95°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
DS1859
Dual, Temperature-Controlled Resistors with
Internally Calibrated Monitors
26
____________________________________________________________________
operation, incremented by one. This data is maintained
as long as VCC is valid. If the most recent address was
the last byte in memory, then the register resets to the
first address.
Once the device address is clocked in and acknowl-
edged by the DS1859 with the R/W bit set to high, the
current address data word is clocked out. The master
does not respond with a zero, but does generate a
STOP condition afterwards.
Single Read
A random read requires a dummy byte write sequence to
load in the data byte address. Once the device and data
address bytes are clocked in by the master and acknowl-
edged by the DS1859, the master must generate another
START condition. The master now initiates a current
address read by sending the device address with the
R/W bit set high. The DS1859 acknowledges the device
address and serially clocks out the data byte.
Sequential Address Read
Sequential reads are initiated by either a current
address read or a random address read. After the mas-
ter receives the first data byte, the master responds
with an acknowledge. As long as the DS1859 receives
this acknowledge after a byte is read, the master can
clock out additional data words from the DS1859. After
reaching address FFh, it resets to address 00h.
The sequential read operation is terminated when the
master initiates a STOP condition. The master does not
respond with a zero.
The following section provides a detailed description of
the 2-wire theory of operation.
2-Wire Serial-Port Operation
The 2-wire serial-port interface supports a bidirectional
data transmission protocol with device addressing. A
device that sends data on the bus is defined as a trans-
mitter, and a device that receives data as a receiver.
The device that controls the message is called a mas-
ter. The devices that are controlled by the master are
slaves. The bus must be controlled by a master device
that generates the serial clock (SCL), controls the bus
access, and generates the START and STOP condi-
tions. The DS1859 operates as a slave on the 2-wire
bus. Connections to the bus are made through the
open-drain I/O lines SDA and SCL. The following I/O
terminals control the 2-wire serial port: SDA, SCL.
Timing diagrams for the 2-wire serial port can be found
in Figures 5 and 6. Timing information for the 2-wire
serial port is provided in the AC Electrical
Characteristics table for 2-wire serial communications.
The following bus protocol has been defined:
◆
Data transfer may be initiated only when the bus is
not busy.
◆
During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
SDA
SCL
tHD:STA
tLOW
tHIGH
tR
tF
tBUF
tHD:DAT
tSU:DAT
REPEATED
START
tSU:STA
tHD:STA
tSU:STO
tSP
STOP
START
Figure 6. 2-Wire AC Characteristics
相關PDF資料 |
PDF描述 |
|---|---|
| FST3125M | IC SWITCH BUS 4BIT TTL 14SOIC |
| FST3126M | IC SWITCH BUS 4BIT TTL 14SOIC |
| FST3253MTC | MUX/DEMUX DUAL 4:1 TTL 16TSSOP |
| MK3754DLF | IC VCXO/PLL CLK SYNTHESIZR 8SOIC |
| MS3108E32-5S | CONN PLUG 2POS RT ANG W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS185XK | 功能描述:數字電位計開發工具 RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V |
| DS1861B | 制造商:Maxim Integrated Products 功能描述:CLOSED LOOP LASER CONTROLLER BGA - Trays |
| DS1861B+ | 功能描述:激光驅動器 Closed Loop Laser Control RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| DS1861E | 制造商:Maxim Integrated Products 功能描述:LASER DRVR 1CH 14TSSOP - Rail/Tube |
| DS1861E+ | 功能描述:激光驅動器 Closed Loop Laser Control RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。