- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1825U+T&R (Maxim Integrated)IC THERMOMETER DIGITAL 8-USOP Datasheet資料下載
參數資料
| 型號： | DS1825U+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 10/21頁 |
| 文件大小： | 287K |
| 描述： | IC THERMOMETER DIGITAL 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | 寄存器庫，變簽式暫存器 |
| 輸出類型： | 數字 |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 3.7 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
DS1825 Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID
10 of 21
HARDWARE CONFIGURATION
The 1-Wire bus has by definition only a single data line. Each device (master or slave) interfaces to the data line
through an open-drain or 3-state port. This allows each device to release the data line when the device is not
transmitting data so the bus is available for use by another device. The 1-Wire port of the DS1825 (the DQ pin) is
open drain with an internal circuit equivalent to that shown in Figure 10.
The 1-Wire bus requires an external pullup resistor of approximately 5kW; thus, the idle state for the 1-Wire bus is
high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle state if the transaction
is to resume. Infinite recovery time can occur between bits so long as the 1-Wire bus is in the inactive (high) state
during the recovery period. If the bus is held low for more than 480ms, all components on the bus will be reset.
Figure 10. HARDWARE CONFIGURATION
TRANSACTION SEQUENCE
The transaction sequence for accessing the DS1825 is as follows:
Step 1. Initialization
Step 2. ROM Command (followed by any required data exchange)
Step 3. DS1825 Function Command (followed by any required data exchange)
It is very important to follow this sequence every time the DS1825 is accessed, as the DS1825 will not respond if
any steps in the sequence are missing or out of order. Exceptions to this rule are the Search ROM [F0h] and Alarm
Search [ECh] commands. After issuing either of these ROM commands, the master must return to Step 1 in the
sequence.
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence consists of a
reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the slave(s). The presence
pulse lets the bus master know that slave devices (such as the DS1825) are on the bus and are ready to operate.
Timing for the reset and presence pulses is detailed in the 1-Wire SIGNALING section.
ROM COMMANDS
After the bus master has detected a presence pulse, it can issue a ROM command. These commands operate on
the unique 64-bit ROM codes of each slave device and allow the master to single out a specific device if many are
present on the 1-Wire bus. These commands also allow the master to determine how many and what types of
devices are present on the bus or if any device has experienced an alarm condition. There are five ROM
commands, and each command is 8 bits long. The master device must issue an appropriate ROM command
before issuing a DS1825 function command. A flowchart for operation of the ROM commands is shown in Figure
11.
V
PU
4.7K
5
A
T
DS1825 1-WIRE PORT
100W
MOSFET
T
R
X
=
RECEIVE
T
X
=
TRANSMIT
1-Wire Bus
DQ
相關PDF資料 |
PDF描述 |
|---|---|
| DS1842N+T&R | IC CURRENT MONITOR 14TDFN |
| DS18B20+PAR | IC THERM MICROLAN PROG-RES TO-92 |
| DS18B20Z/T&R | IC THERM MICROLAN PROG-RES 8SOIC |
| DS2740U+T&R | IC CURRENT GAUGE(15BIT) 8UMAX |
| DS28EA00U+T&R | IC THERMOMETER 1-WIRE 8-USOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1830 | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830+ | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830A | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830A+ | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1830AS | 功能描述:監控電路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。