參數資料
型號: DP83848C-POE-EK
廠商: National Semiconductor
文件頁數: 27/86頁
文件大?。?/td> 0K
描述: BOARD EVALUATION DP83848C
標準包裝: 1
系列: PowerWise®
主要目的: 特殊用途 DC/DC,以太網供電(POE)
輸出及類型: 1,隔離
功率 - 輸出: 24W
輸出電壓: 3.3V
電流 - 輸出: 7.3A
輸入電壓: 39 ~ 57V
穩壓器拓?fù)浣Y(jié)構: 回掃
頻率 - 開關: 250kHz
板類型: 完全填充
已供物品:
已用 IC / 零件: LM5072
相關產品: DP83848CVVX/NOPBTR-ND - TXRX ETHERNET PHYTER 48-LQFP
DP83848CVV-ND - IC TXRX ETHERNET PHYTER 48-LQFP
www.national.com
32
DP
83
84
8C
4.3.6 Jabber Function
The jabber function monitors the DP83848C's output and
disables the transmitter if it attempts to transmit a packet of
longer than legal size. A jabber timer monitors the transmit-
ter and disables the transmission if the transmitter is active
for approximately 85 ms.
Once disabled by the Jabber function, the transmitter stays
disabled for the entire time that the ENDEC module's inter-
nal transmit enable is asserted. This signal has to be de-
asserted for approximately 500 ms (the “unjab” time)
before the Jabber function re-enables the transmit outputs.
The Jabber function is only relevant in 10BASE-T mode.
4.3.7 Automatic Link Polarity Detection and Correction
The DP83848C's 10BASE-T transceiver module incorpo-
rates an automatic link polarity detection circuit. When
three consecutive inverted link pulses are received, bad
polarity is reported.
A polarity reversal can be caused by a wiring error at either
end of the cable, usually at the Main Distribution Frame
(MDF) or patch panel in the wiring closet.
The bad polarity condition is latched in the 10BTSCR regis-
ter. The DP83848C's 10BASE-T transceiver module cor-
rects for this error internally and will continue to decode
received data correctly. This eliminates the need to correct
the wiring error immediately.
4.3.8 Transmit and Receive Filtering
External 10BASE-T filters are not required when using the
DP83848C, as the required signal conditioning is inte-
grated into the device.
Only isolation transformers and impedance matching resis-
tors are required for the 10BASE-T transmit and receive
interface. The internal transmit filtering ensures that all the
harmonics in the transmit signal are attenuated by at least
30 dB.
4.3.9 Transmitter
The encoder begins operation when the Transmit Enable
input (TX_EN) goes high and converts NRZ data to pre-
emphasized Manchester data for the transceiver. For the
duration of TX_EN, the serialized Transmit Data (TXD) is
encoded for the transmit-driver pair (PMD Output Pair).
TXD must be valid on the rising edge of Transmit Clock
(TX_CLK). Transmission ends when TX_EN deasserts.
The last transition is always positive; it occurs at the center
of the bit cell if the last bit is a one, or at the end of the bit
cell if the last bit is a zero.
4.3.10 Receiver
The decoder detects the end of a frame when no additional
mid-bit transitions are detected. Within one and a half bit
times after the last bit, carrier sense is de-asserted.
Receive clock stays active for five more bit times after CRS
goes low, to guarantee the receive timings of the controller.
相關PDF資料
PDF描述
695D335X9050F2T CAP TANT 3.3UF 50V 10% 2414
ISL62881CCPUEVAL2Z EVAL BOARD ISL62881CCPU 28QFN
MDC3105LT1 IC RELAY/DRVR INDUCT LOAD SOT23
LM4040D30ILPRE3 IC VREF SHUNT PREC 3V TO-92-3
ASPI-0602S-820M-T INDUCTOR POWER 82UH 0602 SMD
相關代理商/技術參數
參數描述
DP83848CVV 制造商:Texas Instruments 功能描述:IC, 10/100 ETHERNET PHY, SMD, LQFP48
DP83848CVV/NOPB 功能描述:以太網 IC PHYTER COMMERCIAL TEMP SGL PORT RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
DP83848CVV/NOPB 制造商:Texas Instruments 功能描述:Ethernet Transceiver
DP83848CVVX 制造商:Texas Instruments 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin LQFP T/R
DP83848CVVX/NOPB 功能描述:以太網 IC PHYTER COMMERCIAL TEMP SGL PORT RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray