參數資料
型號： CS51313GDR16
廠商： ZF Electronics Corporation
元件分類： 基準電壓源/電流源
英文描述： Micropower 5V, 100mA Low Dropout Linear Regulator
中文描述： 微5V的，100mA的低壓差線性穩壓器
文件頁數： 16/20頁
文件大小： 248K
代理商： CS51313GDR16
where
P
GATE(H)
= upper MOSFET gate driver (IC) losses;
Q
GATE(H)
= total upper MOSFET gate charge;
F
SW
= switching frequency;
V
GATE(H)
= upper MOSFET gate voltage.
The lower (synchronous) MOSFET gate driver (IC) losses
are:
P
GATE(L)
= Q
GATE(L)
×
F
SW
×
V
GATE(L)
,
where
P
GATE(L)
= lower MOSFET gate driver (IC) losses;
Q
GATE(L)
= total lower MOSFET gate charge;
F
SW
= switching frequency;
V
GATE(L)
= lower MOSFET gate voltage.
The junction temperature of the control IC is primarily a
function of the PCB layout, since most of the heat is
removed through the traces connected to the pins of the
IC.
Step 9: Slope Compensation
Voltage regulators for today’s advanced processors are
expected to meet very stringent load transient require-
ments. One of the key factors in achieving tight dynamic
voltage regulation is low ESR at the CPU input supply
pins. Low ESR at the regulator output results in low out-
put voltage ripple. The consequence is, however, that
there’s very little voltage ramp at the control IC feedback
pin (V
FB
) and regulator sensitivity to noise and loop insta-
bility are two undesirable effects that can surface. The per-
formance of the CS51313-based CPU V
CC(CORE)
regulator is
improved when a fixed amount of slope compensation is
added to the output of the PWM Error Amplifier (COMP
pin) during the regulator Off-Time. Referring to Figure 12,
the amount of voltage ramp at the COMP pin is dependent
on the gate voltage of the lower (synchronous) FET and the
value of resistor divider formed by R1and R2.
V
SLOPECOMP
= V
GATE(L)
×
(
)
×
(1
e ),
where
V
SLOPECOMP
= amount of slope added;
V
GATE(L)
= lower MOSFET gate voltage;
R1, R2 = voltage divider resistors;
t = t
OFF
(switch off-time);
τ
= RC constant determined by C1 and the parallel com-
bination of R1, R2 (Figure 12), neglecting the low driver
output impedance
The artificial voltage ramp created by the slope compensa-
tion scheme results in improved control loop stability pro-
vided that the RC filter time constant is smaller than the
off-time cycle duration (time during which the lower MOS-
FET is conducting).
Step 10: Selection of Current Limit Filter Components
The current limit filter is implemented by a 0.1μF ceramic
capacitor across and two 510
resistors in series with the
V
FB
and V
OUT
current limit comparator input pins. They
provide a time constant
τ
= RC = 100μs, which enables the
circuit to filter out noise and be immune to false triggering,
caused by sudden and fast load changes. These load tran-
sients can have slew rates as high as 20A/μs.
Adaptive voltage positioning is used to help keep the out-
put voltage within specification during load transients. To
implement adaptive voltage positioning a “Droop
Resistor” must be connected between the output inductor
and output capacitors and load. This resistor carries the
full load current and should be chosen so that both DC and
AC tolerance limits are met. An embedded PC trace resis-
tor has the distinct advantage of near zero cost implemen-
tation. However, this droop resistor can vary due to three
reasons: 1) the sheet resistivity variation caused by varia-
tion in the thickness of the PCB layer; 2) the mismatch of
L/W; and 3) temperature variation.
1) Sheet Resistivity
For one ounce copper, the thickness variation is typically
1.26 mil to 1.48 mil. Therefore the error due to sheet resis-
tivity is:
1.48 - 1.26
1.37
= ±8%.
2) Mismatch due to L/W
The variation in L/W is governed by variations due to the
PCB manufacturing process. The error due to L/W mis-
match is typically 1%.
3) Thermal Considerations
Due to I
2
×
R power losses the surface temperature of the
droop resistor will increase causing the resistance to
increase. Also, the ambient temperature variation will con-
tribute to the increase of the resistance, according to the
formula:
R = R
20
[1+
α
20
(
Τ
20)],
where
R
20
= resistance at 20
C;
0.00393
C
α
=
;
T
=
operating temperature;
R = desired droop resistor value.
For temperature T = 50
C, the % R change = 12%.
Droop Resistor Tolerance
Tolerance due to sheet resistivity variation
Tolerance due to L/W error
Tolerance due to temperature variation
Total tolerance for droop resistor
In order to determine the droop resistor value the nominal
voltage drop across it at full load has to be calculated. This
voltage drop has to be such that the output voltage at full
load is above the minimum DC tolerance spec:
±8%
1%
12%
21%
“Droop” Resistor for Adaptive Voltage Positioning
and Current Limit
-t
R2
R1 + R2
Application Information: continued
C
16
相關PDF資料
PDF描述
CS51313 Micropower 5V, 100mA Low Dropout Linear Regulator
CS5132GDW24 Dual Output CPU Buck Controller
CS5132GDWR24 Aluminum Electrolytic Radial Lead High Ripple, Long Life Capacitor; Capacitance: 47uF; Voltage: 250V; Case Size: 12.5x20 mm; Packaging: Bulk
CS5132 Dual Output CPU Buck Controller
CS5150HGD16 CPU 4-Bit Synchronous Buck Controller
相關代理商/技術參數
參數描述
CS-5132 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Output CPU Buck Controller
CS5132DW24 制造商:ON Semiconductor 功能描述:
CS-5132DW24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller
CS-5132DWR24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller
CS5132HGDW24 制造商:Harris Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*