參數資料
型號: COP8SDR9LVA8
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 微控制器/微處理器
英文描述: 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
中文描述: 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 18/80頁
文件大?。?/td> 972K
代理商: COP8SDR9LVA8
9.0 Pin Descriptions
(Continued)
Writing a “1” to bit 6 of the Port G Configuration Register
enables the MICROWIRE/PLUS to operate with the alter-
nate phase of the SK clock. The G7 configuration bit, if set
high, enables the clock start up delay after HALT when the
R/C clock configuration is used.
Config. Reg.
CLKDLY
Alternate SK
Data Reg.
HALT
IDLE
G7
G6
Port G has the following alternate features:
G7 CKO Oscillator dedicated output
G6 SI (MICROWIRE/PLUS Serial Data Input)
G5 SK (MICROWIRE/PLUS Serial Clock)
G4 SO (MICROWIRE/PLUS Serial Data Output)
G3 T1A (Timer T1 I/O)
G2 T1B (Timer T1 Capture Input)
G1 WDOUT WATCHDOG and/or Clock Monitor if WATCH-
DOG enabled, otherwise it is a general purpose I/O
G0 INTR (External Interrupt Input)
G0 through G3 are also used for In-System Emulation.
Port L is an 8-bit I/O port. All L-pins have Schmitt triggers on
the inputs.
Port L supports the Multi-Input Wake-Up feature on all eight
pins. Port L has the following alternate pin functions:
L7 Multi-Input Wake-up or T3B (Timer T3B Input)
L6 Multi-Input Wake-up or T3A (Timer T3A Input/Output)
L5 Multi-Input Wake-up or T2B (Timer T2B Input)
L4 Multi-Input Wake-up or T2A (Timer T2A Input/Output)
L3 Multi-Input Wake-up and/or RDX (USART Receive)
L2 Multi-Input Wake-up or TDX (USART Transmit)
L1 Multi-Input Wake-up and/or CKX (USART Clock) (Low
Speed Oscillator Output)
L0 Multi-Input Wake-up (Low Speed Oscillator Input)
Port D is an 8-bit output port that is preset high when RESET
goes low. The user can tie two or more D port outputs
(except D2) together in order to get a higher drive.
Note: Care must be exercised with the D2 pin operation. At
RESET, the external loads on this pin must ensure that the
output voltages stay above 0.7 V
to prevent the chip from
entering special modes. Also keep the external loading on
D2 to less than 1000 pF.
9.1 EMULATION CONNECTION
Connection to the emulation system is made via a 2 x 7
connector which interrupts the continuity of the RESET, G0,
G1, G2 and G3 signals between the COP8 device and the
rest of the target system (as shown in
Figure 6
). This con-
nector can be designed into the production pc board and can
be replaced by jumpers or signal traces when emulation is
no longer necessary. The emulator will replicate all functions
of G0 - G3 and RESET. For proper operation, no connection
should be made on the device side of the emulator connec-
tor.
10138906
FIGURE 3. I/O Port Configurations
10138907
FIGURE 4. I/O Port Configurations—Output Mode
10138908
FIGURE 5. I/O Port Configurations—Input Mode
C
www.national.com
18
相關PDF資料
PDF描述
COP8SCR9KMT7 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8CSDR9KMT7 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SBR9HLQ8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SCR9HLQ8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SDR9HLQ8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
相關代理商/技術參數
參數描述
COP8SE 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM
COP8SE_FAMILY 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
COP8SEC5 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM
COP8SEC516M 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM
COP8SEC516M7 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller