參數資料
型號： CLC031AVEC
廠商： Motorola, Inc.
英文描述： SMPTE 292M/259M Digital Video Deserializer / Descrambler with Video and Ancillary Data FIFOs
中文描述： 的SMPTE 292M/259M數字視頻解串器/解擾器的視頻和輔助數據FIFO
文件頁數： 20/31頁
文件大小： 399K
代理商： CLC031AVEC
Device Operation
(Continued)
TABLE 3. Control Register Addresses
Register Name
Address
Hexadecimal
01
02
03
04
05
06
07
08
17
18
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
55
56
67
EDH 0
EDH 1
EDH 2
ANC 0
ANC 1
ANC 2
ANC 3
ANC 4
ANC 5
ANC 6
FORMAT 0
FORMAT 1
TEST 0
VIDEO INFO 0
I/O PIN 0 CONFIG
I/O PIN 1 CONFIG
I/O PIN 2 CONFIG
I/O PIN 3 CONFIG
I/O PIN 4 CONFIG
I/O PIN 5 CONFIG
I/O PIN 6 CONFIG
I/O PIN 7 CONFIG
VIDEO CONTROL 0
VIDEO CONTROL 1
REFERENCE CLOCK
EDH 0 (register 01h)
The EDH Full-Field flags
F/F UES
,
F/F IDA
,
F/F IDH
,
F/F
EDA
and
F/F EDH
are defined in SMPTE RP 165. The flags
are updated automatically when the EDH function is enabled
and data is being received.
The
EDH ENABLE
bit, when set, enables operation of the
EDH generator function during SD operation. The default
condition of this bit is set (ON).
The
EDH FORCE
bit, when set, causes updated EDH pack-
ets to be inserted in the parallel output data regardless of the
previous condition of EDH checkwords and flags in the input
serial data. This function may be used in situations where
video content has been edited thus making the previous
EDH information invalid. The default condition of this bit is
reset (OFF).
The
CRC ERROR
bit indicates that errors in either the EDH
checksums (SD) or CRC checkwords (HD) were detected in
the serial input data. This bit is a combined function which
indicates the presence of either EDH errors during SD op-
eration or CRC errors during HD operation.
EDH 1 (register 02h)
The EDH Active Picture flags
A/P UES
,
A/P IDA
,
A/P IDH
,
A/P EDA
and
A/P EDH
are defined in SMPTE RP 165. The
flags are updated automatically when the EDH function is
enabled and data is being received.
Specific types of CRC errors in incoming HD serial data are
reported in the
CRC ERROR LUMA
and
CRC ERROR
CHROMA
bits.
The
CRC REPLACE
bit, when set, causes the CRCs in the
incoming data to be replaced with CRCs calculated by the
CLC031A. The bit is normally reset (OFF).
EDH 2 (register 03h)
The EDH Ancillary Data flags
ANC UES
,
ANC IDA
,
ANC
IDH
,
ANC EDA
and
ANC EDH
are defined in SMPTE RP
165. The flags are updated automatically when the EDH
function is enabled and data is being received.
The status of EDH flag errors in incoming SD serial data are
reported in the
ffFlagError
,
apFlagError
and
ancFlagError
bits. Each of these bits is the logical-OR of the correspond-
ing EDH and EDA flags.
ANC 0 (Address 04h)
The
V FIFO Depth[2:0]
bits control the depth of the video
FIFO which preceeds the parallel output data drivers. The
depth can be set from 0 to 4 stages by writing the corre-
sponding binary code into these bits. For example: to set the
Video FIFO depth at two registers, load 11010XXXXXb into
the ANC 0 control register (where X represents the other
functional bits of this register).
Note:
When changing some but not all bits in a register and
to retain unchanged other data previously stored in the
register, read the register’s contents and logically-OR this
with the new data. Then write the modified data back into the
register.
Flags for
ANC FIFO EMPTY
,
ANC FIFO 90% FULL
,
ANC
FIFO FULL
and
ANC FIFO OVERRUN
are available in the
configuration and control register set. These flags can also
be assigned as outputs on the multi-function I/O port.
ANC
FIFO EMPTY
when set indicates that the FIFO contains no
data.
ANC FIFO 90% FULL
indicates when the FIFO is at
90% of capacity. Since it is virtually impossible for the host
processor to begin extracting data from the FIFO after it has
been flagged as full without the possibility of an overrun
condition occurring,
ANC FIFO 90% FULL
is used as an
advanced command to the host to begin extracting data from
the FIFO. To be used properly,
ANC FIFO 90% FULL
should
be assigned as an output on the multi-function I/O port and
monitored by the host system. Otherwise, inadvertent loss of
ancillary packet data could occur.
ANC FIFO FULL
when set
indicates that the FIFO registers are completely filled with
data.
The
ANC FIFO OVERRUN
flag indicates that an attempt to
write data into a full FIFO has occurred.
ANC FIFO OVER-
RUN
can be reset by reading the bit’s status via the ancillary/
Control port. If an overrun occurrs, the status of the FIFO
message tracking will be invalidated. In this event, the FIFO
should be flushed to reset the message tracking pointers.
Any messages then in the FIFO will be lost.
The
ANC Checksum Force
bit, under certain conditions,
enables the overwriting of Ancillary Data checksums re-
ceived in the data. Calculation and insertion of new Ancillary
Data checksums is controlled by the
ANC Checksum Force
bit. If a checksum error is detected (calculated and received
checksums do not match) and the
ANC Checksum Force
bit is set, the
ANC Checksum Error
bit is set and a new
checksum is inserted in the Ancillary Data replacing the
previous one. If a checksum error is detected and the
ANC
Checksum Force
bit is not set, the checksum mismatch is
C
www.national.com
20
相關PDF資料
PDF描述
CLC031 SMPTE 292M/259M Digital Video Deserializer / Descrambler with Video and Ancilliary Data FIFOs
CLC031VEC SMPTE 292M/259M Digital Video Deserializer / Descrambler with Video and Ancilliary Data FIFOs
CLC034 SMPTE 292M / 259M Adaptive Cable Equalizer
CLC034MA SMPTE 292M / 259M Adaptive Cable Equalizer
CLC103 Fast Settling, High Current Wideband Op Amp
相關代理商/技術參數
參數描述
CLC031AVEC/NOPB 制造商:Texas Instruments 功能描述:Digital Video Deserializer 64-Pin TQFP
CLC03-1N0_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-1N2_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-1N5_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-1N8_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*