- 您現在的位置：買賣IC網 > PDF目錄379893 > CLC014 (National Semiconductor Corporation) Adaptive Cable Equalizer for High-Speed Data Recovery(應用于高速數據恢復的可調電纜均衡器) PDF資料下載
參數資料
| 型號： | CLC014 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Adaptive Cable Equalizer for High-Speed Data Recovery(應用于高速數據恢復的可調電纜均衡器) |
| 中文描述： | 高自適應電纜均衡器高速數據恢復（應用于高速數據恢復的可調電纜均衡器） |
| 文件頁數： | 10/18頁 |
| 文件大?。?/td> | 519K |
| 代理商： | CLC014 |
Output Interfacing
(Continued)
may be used. The resistive divider network provides 75
ter-
mination and establishes proper ECL levels. This circuit con-
sumes slightly more power than the previous circuits.
Design Guidelines
SELECTING THE AUTOMATIC EQUALIZER CAPACITOR
The AEC capacitor sets the loop time constant
τ
for the
equalizer’s adaptive loop response time. The following for-
mula is used to set the loop time constant:
τ
= R
C
AEC
10
6
R is a conversion factor that is set by internal equalizer pa-
rameters and cable length. For Belden 8281 coaxial cable,
the R values are (
τ
= μs, C
AEC
in pF):
Cable
Length
100 meters
200 meters
300 meters
R Value
(Ohms)
15000
20000
32000
For example, a C
AEC
value of 100 pF results in an adaptive
loop time constant of 2 μs at 200 meters of cable.
CONNECTION AND OPERATION OF CD AND MUTE
Carrier Detect (CD)
is a CMOS output that indicates the
presence of equalized data from the filter. This CD output
can be connected to MUTE to suspend changes in the data
outputs DO and DO, if no valid signal exists. This simple
configuration prevents random output transitions due to
noise. For sparse transition patterns it is recommended that
a capacitor be connected to CD as shown in Figure 1
Add a capacitor to pin 5 to slow the response time of Carrier
Detect when Carrier Detect is connected to MUTE. The ca-
pacitor reduces sensitivity to pathological patterns. Patho-
logical patterns are defined as sparse data sequences with
few transitions.
OUTPUT EYE MONITOR OEM CONNECTIONS
The OEM is a high-speed, buffered output for monitoring the
equalized eye pattern prior to the output comparator. Its out-
put is designed to drive an AC-coupled 50
coaxial cable
with a series 50
backmatch resistor. The cable should be
terminated with 50
at the oscilloscope. Figure 1 shows a
schematic with a typical connection.
MINIMUM DATA TRANSITIONS
The CLC014 specifies a minimum transition rate. For the
CLC014 this sets the minimum data rate for transmitting data
through any cable medium. The CLC014 minimum average
transition density is found in the Electrical Characteristics
section of the datasheet.
POWER SUPPLY OPERATION AND THERMAL
CONSIDERATIONS
The CLC014 operates from either +5V or 5.2V single sup-
plies. Refer to Figure 1 when operating the part from +5V.
When operating with a 5.2V supply, the V
pins should be
bypassed to ground. The evaluation board and associated
literature provide for operation from either supply.
Maximum power dissipation occurs at minimum cable
length. Under that condition, I
CC
= 58 mA.
Total power dissipated:
P
T
= (58 mA)(5V) = 290 mW
Power in the load:
P
L
= (0.7V)(11 mA) + (37.5)(11 mA)
2
= 12 mW
Maximum power dissipated on the die:
P
DMAX
= P
T
–P
L
= 278 mW
Junction Temperature =
(
θ
JA
)(278 mW) + T
A
= T
A
+ 26C
DS100056-27
FIGURE 7. Alternative Load Terminated
Output Interface
C
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| CLC016ACQ | Data Retiming PLL with Automatic Rate Selection |
| CLC016AJQ | Data Retiming PLL with Automatic Rate Selection |
| CLC016 | Data Retiming PLL with Automatic Rate Selection(帶自動速率選擇的數據重定時PLL) |
| CLC018AJVJQ | Circular Connector; No. of Contacts:41; Series:MS27473; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:20-41 RoHS Compliant: No |
| CLC018 | 8 x 8 Digital Crosspoint Switch, 1.4 Gbps(8 x 8數字交點開關，1.4 Gbps) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CLC014_03 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Adaptive Cable Equalizer for High-Speed Data Recovery |
| CLC014AJE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:IC CABLE EQUALIZER HI SPEED SMD 制造商:Texas Instruments 功能描述:IC, ADAPTIVE CABLE EQUALIZER, SOIC-14, IC Function:Adaptive Cable Equalizer, Bri |
| CLC014AJE/NOPB | 功能描述:IC CABLE EQUALIZER ADAPTV 14SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| CLC014AJE/NOPB | 制造商:Texas Instruments 功能描述:Buffer / Driver / Receiver Logic IC |
| CLC014AJE-TR13/NOPB | 功能描述:IC CABLE EQUALIZER ADAPT 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發(fā)布緊急采購，3分鐘左右您將得到回復。