- 您現在的位置：買賣IC網 > PDF目錄166442 > BMP-15/1.3-D48 (MURATA POWER SOLUTIONS INC) 2-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | BMP-15/1.3-D48 |
| 廠商： | MURATA POWER SOLUTIONS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL PACKAGE-10 |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 167K |
| 代理商： | BMP-15/1.3-D48 |
40
35
30
25
20
15
10
5
0
O
u
tp
u
tP
o
w
e
r(W
a
tts
)
Ambient Temperature (°C)
–40
0
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Natural Convection Cooling
150 Linear Feet Per Minute
300 Linear Feet Per Minute
Figure 5a. Temperature Derating Without Heat Sink
Figure 5b. Temperature Derating With Heat Sink
D48 Models (40 Watts)
O
u
tp
u
tP
o
w
e
r(W
a
tts
)
Ambient Temperature (°C)
40
35
30
25
20
15
10
5
0
–40
0
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Natural Convection Cooling
150 Linear Feet Per Minute
300 Linear Feet Per Minute
Temperature Derating and Electrical Performance Curves
Output Power
BMP Model, dual-output DC/DC converters incorporate a design tradeoff be-
tween total available output power and input voltage range. The total available
power is a function of both the nominal input voltage and the "width" of the
input voltage range. For a given nominal input (24V or 48V), narrower ranges
(2:1 vs. 4:1) have more available power. For a given "width" of input range
(2:1 or 4:1), higher nominal inputs (48V vs. 24V) have more available power.
Each device, as indicated by its part-number sufx (Q12, Q48, D24 or D48)
has a total output power limitation of 25, 30, 35 or 40 Watts, respectively.
Observing these power limitations is the user's responsibility.
As indicated by its Part Number Structure, each ±5V, ±12V or ±15V BMP
device is capable of sourcing up to ±4, ±1.65 or ±1.3 Amps, respectively.
Users have the exibility of loading either output up to these limits; however
you must be extremely careful not to exceed the total output power rating of
any given device. If, for example, a ±5V device with a 30W power rating
(BMP-5/4-Q48) is sourcing 4A from its +5V output (representing 20W of
+Output power), that device can only supply an additional 10W (2 Amps)
from its –Output.
As a consequence of this "power-allocation" exibility, the denition of "full
load," as the condition under which performance specications are tested
and listed, is ambiguous. The following table lists the positive and negative
output currents that DATEL uses to dene each device’s "full load."
Threaded Inserts and Heatsink Installation
CAUTION: Do not use the threaded inserts to bolt the converter down to a
PC board. That will place unnecessary force on the mounting pins. Instead,
the converter is held securely by only soldering the mounting pins.
When attaching the heat sink from above the converter, use a maximum
torque of 2 inch-pounds (0.23 N-m) on the 4-40 bolts to avoid damaging the
threaded inserts. Use a tiny amount of fastener adhesive or 4-40 lockwashers
to secure the bolts.
Soldering Guidelines
Murata Power Solutions recommends the specications below when installing these converters. These specications vary depending on the solder type. Exceeding these
specications may cause damage to the product. Be cautious when there is high atmospheric humidity. We strongly recommend a mild pre-bake (100° C. for 30 minutes). Your
production environment may differ; therefore please thoroughly review these guidelines with your process engineers.
Wave Solder Operations for through-hole mounted products (THMT)
For Sn/Ag/Cu based solders:
For Sn/Pb based solders:
Maximum Preheat Temperature
115° C.
Maximum Preheat Temperature
105° C.
Maximum Pot Temperature
270° C.
Maximum Pot Temperature
250° C.
Maximum Solder Dwell Time
7 seconds
Maximum Solder Dwell Time
6 seconds
BMP Models
25-40W, Dual Output, DC/DC Converters
MDC_BMP25-40W.C01 Page 6 of 6
www.murata-ps.com/support
相關PDF資料 |
PDF描述 |
|---|---|
| BMR4532001/002 | DC-DC REG PWR SUPPLY MODULE |
| BN1A4M | The BN1A4M is designed for use in medium speed switching circuit. |
| BN1A4P | PNP SILICON TRANSISTOR |
| BN1A4Z | on-chip resistor PNP silicon epitaxial transistor For mid-speed switching |
| BN87C51FA12 | 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BMP180 | 功能描述:SENSOR PRESSURE ABS RoHS:是 類別:傳感器，轉換器 >> 壓力 系列:- 標準包裝:100 系列:* |
| BMP180-0273300244 | 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8-3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA 7-pin 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8 to 3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA-7 |
| BMP180-0273300244001 | 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8 to 3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA-7 |
| BMP180-0273300244-CUT TAPE | 制造商:BOSCH 功能描述:BMP180 Series 1.8-3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA 7-pin |
| BMP180-0330SB0244 | 制造商:Bosch Sensortec 功能描述:Shuttle Board for BMP180 Series Pressure Sensor |
發布緊急采購，3分鐘左右您將得到回復。