- 您現在的位置：買賣IC網 > PDF目錄166442 > BMP-15/1.3-D48 (MURATA POWER SOLUTIONS INC) 2-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | BMP-15/1.3-D48 |
| 廠商： | MURATA POWER SOLUTIONS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL PACKAGE-10 |
| 文件頁數： | 4/7頁 |
| 文件大小： | 167K |
| 代理商： | BMP-15/1.3-D48 |
Floating Outputs
Since these are isolated DC/DC converters, their outputs are "oating." Any
BMP model may be congured to produce an output of 10V, 24V or 30V (for
±
5V, ±12V or ±15V models, respectively) by applying the load across the
+Output and –Output (pins 9 and 6), with either output grounded. The Com-
mon (pin 8) should be left open. Minimum 20% loading is recommended
under these conditions. The total output voltage span may be externally
trimmed as described below.
Performance/Functional Specications
Typical @ TA = +25°C under nominal line voltage and "full-load" conditions, unless noted.
Input
Input Voltage Range:
Q12 Models
10-36 Volts (24V nominal)
D24 Models
18-36 Volts (24V nominal)
Q48 Models
18-75 Volts (48V nominal)
D48 Models
36-75 Volts (48V nominal)
Input Current
See Ordering Guide
Input Filter Type
Pi
Overvoltage Shutdown:
Q12 and D24 Models
40 Volts
Q48 and D48 Models
80 Volts
Reverse-Polarity Protection
Yes (Instantaneous, 6A maximum)
On/Off Control (Pin 5)
TTL high (or open) = on, low = off
Output
VOUT Accuracy (50% load)
±1%, maximum
Temperature Coefcient
±0.02% per °C
Ripple/Noise (20MHz BW)
See Ordering Guide
Line/Load Regulation
See Ordering Guide
Efciency
See Ordering Guide
Isolation Voltage
1500Vdc, minimum
Isolation Capacitance
620pF
Current Limiting
Continuous, auto-recovery
Overvoltage Protection
Zener/transorb clamps, magnetic feedback
Dynamic Characteristics
Transient Response (50% load step)
300μsec max. to ±1.5% of nal value
Switching Frequency
125kHz (±10%)
Environmental
Operating Temperature (ambient):
Without Derating
–40 to +60°C (Model dependent)
With Derating
to +90°C (See Derating Curves)
Maximum Case Temperature
+90°C
Storage Temperature
–40 to +105°C
Relative Humidity
To 85°C /85% RH, non-condensing
Physical
Safety
Designed to meet UL/cUL/EN/IEC 60950-1
Dimensions
2.04" x 3.04" x 0.55" (51.8 x 77.2 x 14mm)
Shielding
5-sided
Case Connection
Pin 4
Case Material
Aluminum, black anodized nish
with plastic header
Flammability Rating
UL94V-0
Pin Material
Gold-plated copper alloy with nickel
underplate
Weight
6 ounces (170 grams)
These converters require a minimum 10% loading on each output to maintain
specied regulation. Operation under no-load conditions will not damage these devices;
however they may not meet all listed specications.
"Full load" varies by part number and is determined by the input voltage range as indi
cated by the part number sufx. See Technical Notes and Output Power Considerations.
Application-specic input/output ltering can be recommended or perhaps added inter
nally upon request. Contact DATEL Applications Engineering for details.
Applying a voltage to the On/Off Control pin when no input power is applied to the con
verter can cause permanent damage to the converter.
Listed specication is for input-to-output isolation. Input-to-case and output-to-case
isolation is 1000Vdc, minimum.
Filtering and Noise Reduction
All BMP 25-40 Watt DC/DC Converters achieve their rated ripple and noise
specications without the use of external input/output capacitors. In criti-
cal applications, input/output ripple and noise may be further reduced by
installing electrolytic capacitors across the input terminals and/or low-ESR
tantalum or electrolytic capacitors across the output terminals. Output
capacitors should be connected between their respective output pin (pin 6 or
9) and Common (pin 8). See Figure 7. The caps should be located as close
to the converters as possible. Typical values are listed in the below. In many
applications, using values greater than those listed will yield better results.
To Reduce Input Ripple
"Q12, D24" Models
47μF, 50V
"Q48, D48" Models
10μF, 100V
To Reduce Output Ripple
±5V Outputs
47μF, 10V, Low ESR
±12/15V Outputs
22μF, 20V, Low ESR
Input Voltage:
Q12/D24 Models
44 Volts
Q48/D48 Models
88 Volts
Input Reverse-Polarity Protection
Current must be <6A. Brief
duration only. Fusing recommended.
Output Overvoltage Protection
±5V Outputs
6.8 Volts, limited duration
±12V Outputs
15 Volts, limited duration
±15V Outputs
18 Volts, limited duration
Output Current
Current limited. Max. current and
short-circuit duration are model
dependent.
Storage Temperature
–40 to +105°C
Lead Temperature
See soldering guidelines
These are stress ratings. Exposure of devices to greater than any of these conditions may
adversely affect long-term reliability. Proper operation under conditions other than those
listed in the Performance/Functional Specications Table is not implied.
Absolute Maximum Ratings
TECHNICAL NOTES
VIN Range
Q12
D24
Q48
D48
Fuse Value
4A
3A
2A
Input Fusing
BMP Models
25-40W, Dual Output, DC/DC Converters
MDC_BMP25-40W.C01 Page 4 of 6
www.murata-ps.com/support
相關PDF資料 |
PDF描述 |
|---|---|
| BMR4532001/002 | DC-DC REG PWR SUPPLY MODULE |
| BN1A4M | The BN1A4M is designed for use in medium speed switching circuit. |
| BN1A4P | PNP SILICON TRANSISTOR |
| BN1A4Z | on-chip resistor PNP silicon epitaxial transistor For mid-speed switching |
| BN87C51FA12 | 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BMP180 | 功能描述:SENSOR PRESSURE ABS RoHS:是 類別:傳感器，轉換器 >> 壓力 系列:- 標準包裝:100 系列:* |
| BMP180-0273300244 | 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8-3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA 7-pin 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8 to 3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA-7 |
| BMP180-0273300244001 | 制造商:Bosch Sensortec 功能描述:BMP180 Series 1.8 to 3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA-7 |
| BMP180-0273300244-CUT TAPE | 制造商:BOSCH 功能描述:BMP180 Series 1.8-3.6 V 300 to 1100 hPa Digital Pressure Sensor - LGA 7-pin |
| BMP180-0330SB0244 | 制造商:Bosch Sensortec 功能描述:Shuttle Board for BMP180 Series Pressure Sensor |
發布緊急采購，3分鐘左右您將得到回復。