- 您現在的位置：買賣IC網 > PDF目錄373023 > BM29F400T-90TC x8/x16 Flash EEPROM PDF資料下載
參數資料
| 型號： | BM29F400T-90TC |
| 英文描述： | x8/x16 Flash EEPROM |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 12/37頁 |
| 文件大?。?/td> | 265K |
| 代理商： | BM29F400T-90TC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
BRIGHT
Microelectronics
Inc.
BM29F400T/BM29F400B
- 12 -
Writing the Erase Suspend command during the time-out will result in immediate termination of the
time-out period. Any subsequent writes of the Sector Erase command will be taken as the Erase
Resume command (30H). Note that any other commands during the time-out will
RESET
the device
to the Read mode. The address pins are "don't cares" when writing the Erase Suspend or Erase
Resume commands.
When the Erase Suspend command is written during a Sector Erase operation, the chip will take
between 1
μ
S and 230
μ
S to suspend the erase operation and go into Erase Suspended mode.
During this time, the system can monitor the Data Polling or Toggle Bit write operation status flags to
determine when the device has entered erase suspend mode (see Write Operation Status section.)
The system must use an address of an erasing sector to monitor Data Polling or Toggle Bit to
determine if the Sector Erase operation has been suspended.
In Erase Suspend mode, the system can read data from any sector that is not being erased. A read
from a sector being erased will result in write operation status data. After the system writes the Erase
Suspend command and waits until the Toggle Bit stops toggling, data reads from the device may then
be performed (see Write Operation Status section). Any further writes of the Erase Suspend
command at this time will be ignored.
To resume operation of Sector Erase, the Erase Resume command (30H) should be written. Any
further writes of the Erase Resume command at this point will be ignored. Another Erase Suspend
command can be written after the chip has resumed Sector Erase operation.
DQ7
Data
Polling
The BM29F400 device features Data Polling as a method to indicate to the host the status of the
Byte/Word Programming, Chip Erase, and Sector Erase operations. When the Byte/Word
Programming operation is in progress, an attempt to read the device will produce the compliment of
the data last written to DQ7. Upon completion of the Byte/Word Programming operation, an attempt
to read the device will produce the true data last written to DQ7. When the Chip Erase or Sector
Erase operation is in progress, an attempt to read the device will produce a logical "0" at the DQ7
output. Upon completion of the Chip Erase or Sector Erase operation, an attempt to read the device
will produce a logical "1" at the DQ7 output. The flowchart for Data Polling (DQ7) is shown in Figure
3.
For Chip Erase, the Data Polling is valid after the rising edge of the sixth
WE
pulse in the six write
pulse sequence. For Sector Erase, the Data Polling is valid after the last rising edge of the sector
erase
WE
pulse. For both Chip Erase and Sector Erase, Data Polling must be performed at sector
address within any of the sectors being erased and not a protected sector. Otherwise, the Data
Polling status may not be valid. Once the Internal Algorithm operation is close to being completed,
the BM29F400 data pins (DQ7) may change asynchronously while the output enable (
OE
) is
asserted low. This means that the device is driving status information on DQ7 at one instant and valid
data at the next instant of time. Depending on when the system samples the DQ7 output, it may read
status or valid data. Even if the device has completed the Internal Algorithm operation and DQ7 has a
valid data, data outputs on DQ0-DQ6 may be still invalid. Valid data on DQ0-DQ7 will be read on the
successive read attempts.
相關PDF資料 |
PDF描述 |
|---|---|
| BMS-SAX300MM | GUIDE PCB 300MM STRIP |
| BN101 | Optoelectronic |
| BN201 | Optoelectronic |
| BN301 | Optoelectronic |
| BN401 | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BM-2A | 制造商:Anderson Power Products (APP) 功能描述:BENCH MOUNT |
| BM-2BK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CASE DESKTOP |
| BM2LB150FJ-CE2 | 功能描述:2CH LOW SIDE SWITCH IC, 150M OHM 制造商:rohm semiconductor 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOP-J 標準包裝:1 |
| BM2LB300FJ-CE2 | 功能描述:THE BM2LB300FJ-C IS AN AUTOMOTIV 制造商:rohm semiconductor 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOP-J 標準包裝:1 |
| BM2M-C | 功能描述:電線鑒定 Marker Tie Wrap 7.9"L (201mm) Mini RoHS:否 制造商:TE Connectivity / Q-Cees 產品:Labels and Signs 類型: 材料:Vinyl 顏色:Blue 寬度:0.625 in 長度:1 in |
發布緊急采購，3分鐘左右您將得到回復。