參數資料
型號： AT89EB5114-TGSIL
廠商： Atmel
文件頁數： 17/86頁
文件大?。?/td> 0K
描述： IC 8051 MCU FLASH 4K 20SOIC
產品培訓模塊： MCU Product Line Introduction
標準包裝： 38
系列： 89EB
核心處理器： 8051
芯體尺寸： 8-位
速度： 40MHz
外圍設備： POR，PWM，WDT
輸入/輸出數： 11
程序存儲器容量： 4KB（4K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 256 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 6x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 管件
產品目錄頁面： 616 (CN2011-ZH PDF)
24
AT89/83EB5114
4311C–8051–02/08
Timers/Counters
Introduction
The AT8xEB5114 implements two general-purpose, 16-bit Timers/Counters. Although
they are identified as Timer 0, Timer 1, they can be independently configured each to
operate in a variety of modes as a Timer or as an event Counter. When operating as a
Timer, a Timer/Counter runs for a programmed length of time, then issues an interrupt
request. When operating as a Counter, a Timer/Counter counts negative transitions on
an external pin. After a preset number of counts, the Counter issues an interrupt
request.
The Timer registers and associated control registers are implemented as addressable
Special Function Registers (SFRs). Two of the SFRs provide programmable control of
the Timers as follows:
Timer/Counter mode control register (TMOD) and Timer/Counter control register
(TCON) control both Timer 0 and Timer 1.
The various operating modes of each Timer/Counter are described below.
Timer/Counter
Operations
A basic operation is Timer registers THx and TLx (x = 0, 1) connected in cascade to
form a 16-bit Timer. Setting the run control bit (TRx) in the TCON register (see
Figure 15) turns the Timer on by allowing the selected input to increment TLx. When
TLx overflows it increments THx and when THx overflows it sets the Timer overflow flag
(TFx) in the TCON register. Setting the TRx does not clear the THx and TLx Timer reg-
isters. Timer registers can be accessed to obtain the current count or to enter preset
values. They can be read at any time but the TRx bit must be cleared to preset their val-
ues, otherwise the behavior of the Timer/Counter is unpredictable.
The C/Tx# control bit selects Timer operation or Counter operation by selecting the
divided-down system clock or the external pin Tx as the source for the counted signal.
The TRx bit must be cleared when changing the operating mode, otherwise the behavior
of the Timer/Counter is unpredictable.
For Timer operation (C/Tx# = 0), the Timer register counts the divided-down system
clock. The Timer register is incremented once every peripheral cycle.
For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on
the external input pin Tx. The external input is sampled during every S5P2 state. The
Programmer’s Guide describes the notation for the states in a peripheral cycle. When
the sample is high in one cycle and low in the next one, the Counter is incremented. The
new count value appears in the register during the next S3P1 state after the transition
has been detected. Since it takes 12 states (24 oscillator periods in X1 mode) to recog-
nize a negative transition, the maximum count rate is 1/24 of the oscillator frequency in
X1 mode. There are no restrictions on the duty cycle of the external input signal, but to
ensure that a given level is sampled at least once before it changes, it should be held for
at least one full peripheral cycle.
Timer 0
Timer 0 functions as either a Timer or an event Counter in four operating modes.
Figure 7 to Figure 10 show the logic configuration of each mode.
Timer 0 is controlled by the four lower bits of the TMOD register (see Figure 16) and bits
0, 1, 4 and 5 of the TCON register (see Figure 15). The TMOD register selects the
method of Timer gating (GATE0), Timer or Counter operation (T/C0#) and the operating
mode (M10 and M00). The TCON register provides Timer 0 control functions: overflow
flag (TF0), run control bit (TR0), interrupt flag (IE0) and interrupt type control bit (IT0).
For normal Timer operation (GATE0= 0), setting TR0 allows TL0 to be incremented by
the selected input. Setting GATE0 and TR0 allows external pin INT0# to control Timer
相關PDF資料
PDF描述
AT89LP214-20PU MCU 8051 2K FLASH 20MHZ 14-PDIP
AT89LP216-20SU MCU 8051 2K FLASH 20MHZ 16-SOIC
AT89LP4052-20SU IC 8051 MCU FLASH 4K 20SOIC
AT89LP428-20AU MCU 8051 4K FLASH SPI 32TQFP
AT89LP52-20MU IC MCU 8051 8K FLASH SPI 44VQFN
相關代理商/技術參數
參數描述
AT89EB5114-TGSUL 功能描述:8位微控制器 -MCU A/D 4K Flash 256EE RC 4PWM SO20 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89EMK-01 功能描述:EMULATOR FOR MP3 SND1 MCU RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:Keil 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
AT89EVK-01 功能描述:開發板和工具包 - 8051 AT83C24 Kit for TDA8004/8024 rplcmnt RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
AT89ISP 功能描述:電纜組件 ISP CABLE FOR 89S SERIES - ISP CABLE RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規（AWG）:20, 28 長度:0.305 m 顏色:Black, Red
AT89LP2052-16PI 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*