VDD was reduced during " />
參數資料
型號: AT89C5115-RATUM
廠商: Atmel
文件頁數: 28/113頁
文件大小: 0K
描述: IC 8051 MCU FLASH 16K 32VQFP
產品培訓模塊: MCU Product Line Introduction
標準包裝: 1,250
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 40MHz
連通性: UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 20
程序存儲器容量: 16KB(16K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 2K x 8
RAM 容量: 512 x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
數據轉換器: A/D 8x10b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 32-LQFP
包裝: 托盤
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
21
AT89C5115
4128G–8051–02/08
Exiting Power-down Mode
Note:
If
VDD was reduced during the Power-down mode, do not exit Power-down mode until
VDD is restored to the normal operating level.
There are two ways to exit the Power-down mode:
1.
Generate an enabled external interrupt.
The T89C5115 provides capability to exit from Power-down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and
restores the clocks to the CPU and peripherals. Using INTx# input,
execution resumes when the input is released (See Figure 8). Execution
resumes with the interrupt service routine. Upon completion of the interrupt
service routine, program execution resumes with the instruction immediately
following the instruction that activated Power-down mode.
Notes:
1. The external interrupt used to exit Power-down mode must be configured as level
sensitive (INT0# and INT1#) and must be assigned the highest priority. In addition,
the duration of the interrupt must be long enough to allow the oscillator to stabilize.
The execution will only resume when the interrupt is deasserted.
2. Exit from power-down by external interrupt does not affect the SFRs nor the internal
RAM content.
Figure 8. Power-down Exit Waveform Using INT1:0#
2.
Generate a reset.
A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU
and peripherals. Program execution momentarily resumes with the
instruction immediately following the instruction that activated Power-down
mode and may continue for a number of clock cycles before the internal
reset algorithm takes control. Reset initializes the T89C5115 and vectors the
CPU to address 0000h.
Notes:
1. During the time that execution resumes, the internal RAM cannot be accessed; how-
ever, it is possible for the Port pins to be accessed. To avoid unexpected outputs at
the Port pins, the instruction immediately following the instruction that activated the
Power-down mode should not write to a Port pin or to the external RAM.
2. Exit from power-down by reset redefines all the SFRs, but does not affect the internal
RAM content.
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
相關PDF資料
PDF描述
VI-J0P-IX-B1 CONVERTER MOD DC/DC 13.8V 75W
VJ2225A331KBEAT4X CAP CER 330PF 500V 10% NP0 2225
862197-2 LGH, RECEPTACLE ASS'Y
861611-1 CONN RECEPT LGH 1POS BULKHD
ATMEGA168V-10PU IC AVR MCU 16K 10MHZ 28DIP
相關代理商/技術參數
參數描述
AT89C5115-SISUM 功能描述:8位微控制器 -MCU C51 16K Flash ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C5115-TISUM 功能描述:8位微控制器 -MCU 16K Flash ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51-16AA 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash
AT89C51-16AC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51-16AI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash