參數資料
型號: AT89C5115-RATUM
廠商: Atmel
文件頁數: 24/113頁
文件大?。?/td> 0K
描述: IC 8051 MCU FLASH 16K 32VQFP
產品培訓模塊: MCU Product Line Introduction
標準包裝: 1,250
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 40MHz
連通性: UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 20
程序存儲器容量: 16KB(16K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 2K x 8
RAM 容量: 512 x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
數據轉換器: A/D 8x10b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 32-LQFP
包裝: 托盤
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
18
AT89C5115
4128G–8051–02/08
Power Management
Two power reduction modes are implemented in the T89C5115: the Idle mode and the
Power-down mode. These modes are detailed in the following sections. In addition to
these power reduction modes, the clocks of the core and peripherals can be dynamically
divided by 2 using the X2 Mode detailed in Section “Clock”.
Reset Pin
In order to start-up (cold reset) or to restart (warm reset) properly the microcontroller, a
high level has to be applied on the RST pin. A bad level leads to a wrong initialisation of
the internal registers like SFRs, PC, etc. and to unpredictable behavior of the microcon-
troller. A warm reset can be applied either directly on the RST pin or indirectly by an
internal reset source such as a watchdog, PCA, timer, etc.
At Power-up (cold reset)
Two conditions are required before enabling a CPU start-up:
VDD must reach the specified VDD range,
The level on xtal1 input must be outside the specification (VIH, VIL).
If one of these two conditions are not met, the microcontroller does not start correctly
and can execute an instruction fetch from anywhere in the program space. An active
level applied on the RST pin must be maintained until both of the above conditions are
met. A reset is active when the level VIH1 is reached and when the pulse width covers
the period of time where VDD and the oscillator are not stabilized. Two parameters have
to be taken into account to determine the reset pulse width:
VDD rise time (vddrst),
Oscillator startup time (oscrst).
To determine the capacitor the highest value of these two parameters has to be chosen.
The reset circuitry is shown in Figure 5.
Figure 5. Reset Circuitry
Table 12 and Table 13 give some typical examples for three values of VDD rise times,
two values of oscillator start-up time and two pull-down resistor values.
Table 12. Minimum Reset Capacitor for a 50K Pull-down Resistor
oscrst/vddrst
1ms
10ms
100ms
5ms
820nF
1.2F
12F
20ms
2.7F
3.9F
12F
0
VDD
Rrst
Crst
RST pin
Internal reset
Reset input circuitry
相關PDF資料
PDF描述
VI-J0P-IX-B1 CONVERTER MOD DC/DC 13.8V 75W
VJ2225A331KBEAT4X CAP CER 330PF 500V 10% NP0 2225
862197-2 LGH, RECEPTACLE ASS'Y
861611-1 CONN RECEPT LGH 1POS BULKHD
ATMEGA168V-10PU IC AVR MCU 16K 10MHZ 28DIP
相關代理商/技術參數
參數描述
AT89C5115-SISUM 功能描述:8位微控制器 -MCU C51 16K Flash ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C5115-TISUM 功能描述:8位微控制器 -MCU 16K Flash ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51-16AA 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash
AT89C51-16AC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51-16AI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash