參數資料
型號： AS8510-ASST
廠商： ams
文件頁數： 13/47頁
文件大?。?/td> 0K
描述： IC BATTERY MANAGEMENT 20-SSOP
產品培訓模塊： AS8510 Data Acquisition IC
標準包裝： 2,000
類型： 電池管理
輸入類型： 模擬，數字
輸出類型： 模擬，數字
接口： SPI 串行
電流 - 電源： 5mA
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
Revision 3.5
19 - 46
AS8510
Datasheet - Detailed Descr i p ti on
7.4.1 Normal Mode 1 (NOM1)
On Power-on-reset of the device, AS8510 goes into STOP State.
Transition to Normal mode1 (NOM1) occurs when the “START BIT” D0 of Mode Control Register MOD_CTL_REG in Table 33 is set to “1”
through the serial port SPI. Data Rate of voltage and current channels can be independently programmed and both the channels generate
interrupts for every output available from ADC. The interrupt signal is generated on the INT pin. The width of the interrupt pulse is eight cycles of
lp_clk. The data is stable up to the next interrupt. If the data rate is different for the two channels, the interrupt rate would follow the higher rate
among the two channels. Data update can be known by reading the status register. The functionality is explained in the waveform shown in
Figure 5. When the device is configured to NORMAL Mode1 from any mode the configuration should be through the STOP state only.
Figure 5. Normal Mode 1
7.4.2 Normal Mode 2 (NOM2)
NOM2 differs from NOM1 in such a way that it allows for a relaxed data rate at a period of TMC by programming the corresponding register as
long as the amplitude of current is less than a programmed threshold ITHC. However, when, the measured input signal exceeds the programmed
threshold, the data rate is changed to the rate of NOM1 mode.
Transition to NOM2 occurs when the “START BIT” D0 of Mode Control register MOD_CTL_REG in Table 33 is set to 1 and mode control bits to
01 through SPI. In this mode the data rate should be programmed with the time of TMC. An interrupt signal is generated on INT at the rate of TMC
secs with a pulse width of eight cycles of lp_clk. The data is stable up to the next interrupt. The data sample is compared against the programmed
threshold and when it is exceeded, the data sampling rate is changed to provide data at the data rate of NOM1 mode. However, as soon as the
data sample amplitude falls below the programmed threshold, the sampling rate is restored to provide data at the rate of TMC. The functionality is
illustrated in the waveform Figure 6.
Sampling with f1
INT at f1 rate from
current channel
Current Channel
DATA Register
t
I
START
STOP
t
V,T
Sampling with f2
Voltage Channel
DATA Register
Interrupt fromthe current channel is at f1 rate which is integer multiple of f2 rate fromvoltage channel
IDATA
V,TDATA
TINT
相關PDF資料
PDF描述
AS8530-ASOT-002-500 IC TXRX LIN COMPANION 8-SOIC
AS8530A-ASOT-500 IC SYSTEM BASIS CHIP 8-SOIC
AT17F080-30TQI IC FLASH CONFIG 8M 44TQFP
AT17F080A-30QI IC FLASH CONFIG 8M 32TQFP
AT17F16-30TQI IC FLASH CONFIG 16M 44TQFP
相關代理商/技術參數
參數描述
AS8510-ASST-500 功能描述:IC BATTERY MANAGEMENT 20-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AS8510-COPPER-SHUNT 功能描述:DEMO BOARD FOR AS8510 制造商:ams 系列:- 零件狀態:在售 主要用途:接口，數據捕捉 嵌入式:- 使用的 IC/零件:AS8510 主要屬性:- 輔助屬性:圖形用戶界面 所含物品:板 標準包裝:1
AS8510-DB 制造商:ams 功能描述:AS8510 Demo Board
AS8515-ZMFM 制造商:ams 功能描述:IC BATTERY MANAGEMENT 制造商:ams 功能描述:Data Acquisition System w/ Power Management and LIN Transceiver - MLF-32 制造商:ams 功能描述:T&R / MLF 32 (5x5)
AS8515-ZMFP 制造商:ams 功能描述:IC INTERFACE TRANSCEIVER 制造商:ams 功能描述:T&R / MLF 32 (5x5)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*