Figure 3. Block " />
參數資料
型號: AS8510-ASST
廠商: ams
文件頁數: 10/47頁
文件大?。?/td> 0K
描述: IC BATTERY MANAGEMENT 20-SSOP
產品培訓模塊: AS8510 Data Acquisition IC
標準包裝: 2,000
類型: 電池管理
輸入類型: 模擬,數字
輸出類型: 模擬,數字
接口: SPI 串行
電流 - 電源: 5mA
安裝類型: 表面貼裝
封裝/外殼: 20-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 20-SSOP
包裝: 帶卷 (TR)
Revision 3.5
17 - 46
AS8510
Datasheet - Detailed Descr i p ti on
7.3 Digital Implementation of Measurement Path
Figure 3. Block Diagram of Digital Implementation
Figure 3 shows the digital implementation of the decimator and filter to process the 1-bit output of the Modulator. This block receives a 1-bit pulse
density modulated output (MOD_IN) from the second order sigma delta modulator along with the oversampling frequency clock (MOD_CLK).
The MOD_CLK directly goes to a clock division block, which generates chopper clock (CHOP_CLK). The CHOP_CLK can be one of 2kHz or
4kHz selected by Register CLK_REG in Table 33. The MOD_CLK can be either 1MHz or 2MHz. The Decimation is a two phase process. In the
first phase, the R1 down sampling rate can be obtained by selecting either 64 or 128 in Registers DECREG_R1_I, DECREG_R1_V in Table 33.
The 16-bit CIC1 output is dechopped with respect to CHOP_CLK. The output of Dechopper is passed through the CIC2 filter with a decimation
ratio of 1to 32768 in steps of power of 2. This output is then processed through a FIR or Moving Average (MA) filter. FIR Filter is provided to offer
matched low pass filter response typically required in lead acid battery sensor systems. MA filter is used to provide averaged output and the
number of samples for averaging can be any integer value from 1 to 15.
7.4 Modes of Operation
The device operates in four different modes, namely,
Normal Mode 1 (NOM1),
Normal Mode 2 (NOM2),
Standby Mode 1 (SBY1), and,
Standby Mode 2 (SBY2).
The Normal Modes are full-power modes with the exception that in Normal Mode 2, sampling is normally at a programmed lower frequency and
is increased to a higher rate only when a measured input signal level crosses the programmed threshold in the current measurement channel.
The Standby Modes are lower power modes. Sampling is normally at a very low frequency interval. In Standby Mode 2, data sampling can be
carried out only when the internal comparator detects the input current to be greater than the programmed threshold and it generates interrupt on
the INT pin.
The device enters into the “Stop” state on Power On. This is a state where in the data path is inactive and can be entered into from any of the
four Modes. The State transition Diagram involving the state of Stop and the four Modes is illustrated in the Figure 4.
CIC1
64/ 128
CLKDIVISION
BLOCK
Dechopper
FIR/MA
MOD_IN
MOD_CLK
DATAOUT
R1
R1=First decimationratio(64or 128)
R2=Seconddecimationratio(1to32768)
MOD_CLK
R1
CIC2
R2
FIR_MA_SEL
CHP_CLK
fmod / R1
fchop * 2
fchop * 2/ R2
fchop
fmod
fchop * 2/ R2
相關PDF資料
PDF描述
AS8530-ASOT-002-500 IC TXRX LIN COMPANION 8-SOIC
AS8530A-ASOT-500 IC SYSTEM BASIS CHIP 8-SOIC
AT17F080-30TQI IC FLASH CONFIG 8M 44TQFP
AT17F080A-30QI IC FLASH CONFIG 8M 32TQFP
AT17F16-30TQI IC FLASH CONFIG 16M 44TQFP
相關代理商/技術參數
參數描述
AS8510-ASST-500 功能描述:IC BATTERY MANAGEMENT 20-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AS8510-COPPER-SHUNT 功能描述:DEMO BOARD FOR AS8510 制造商:ams 系列:- 零件狀態:在售 主要用途:接口,數據捕捉 嵌入式:- 使用的 IC/零件:AS8510 主要屬性:- 輔助屬性:圖形用戶界面 所含物品:板 標準包裝:1
AS8510-DB 制造商:ams 功能描述:AS8510 Demo Board
AS8515-ZMFM 制造商:ams 功能描述:IC BATTERY MANAGEMENT 制造商:ams 功能描述:Data Acquisition System w/ Power Management and LIN Transceiver - MLF-32 制造商:ams 功能描述:T&R / MLF 32 (5x5)
AS8515-ZMFP 制造商:ams 功能描述:IC INTERFACE TRANSCEIVER 制造商:ams 功能描述:T&R / MLF 32 (5x5)