參數資料
型號: APMOTOR56F8000E
廠商: Freescale Semiconductor
文件頁數: 108/124頁
文件大?。?/td> 0K
描述: KIT DEMO MOTOR CTRL SYSTEM
標準包裝: 1
附件類型: 電機控制器
適用于相關產品: DEMO56F8013,DEMO56F8013-E
相關產品: MC56F8006VWL-ND - DSC 16K FLASH 32MHZ 28-SOIC
MC56F8006VLF-ND - DSC 16K FLASH 32MHZ 48-LQFP
MC56F8006VLC-ND - DSC 16K FLASH 32MHZ 32-LQFP
MC56F8002VWL-ND - DSC 12K FLASH 32MHZ 28-SOIC
DEMO56F8014-E-ND - BOARD DEMO MC56F8014 W/UNIV PS
DEMO56F8014-ND - BOARD DEMO MC56F8014 W/US PS
DEMO56F8014-EE-ND - BOARD DEMO FOR 56F8014
DEMO56F8013-EE-ND - BOARD DEMO FOR 56F8013
MC56F8014VFAE-ND - IC DIGITAL SIGNAL CTRLR 32-LQFP
MC56F8013VFAE-ND - IC DIGITAL SIGNAL CTLR 32-LQFP
更多...
56F8014 Technical Data, Rev. 11
84
Freescale Semiconductor
in order to return to normal unsecured operation. Power-on reset will also reset both.
The user is responsible for directing the device to invoke the flash programming subroutine to reprogram
the word $0000 into program memory location $00 1FF7. This is done by, for example, toggling a specific
pin, or by downloading a user-defined key through serial interfaces.
Note:
Flash contents can only be programmed for 1s to 0s.
7.3 Product Analysis
The recommended method of unsecuring a secured device for product analysis of field failures is via the
method suggested in section 7.2.4. The customer would need to supply Technical Support with the details
of the protocol to access the subroutines in flash. An alternative method for performing analysis on a
secured device would be to mass-erase and reprogram the flash with the original code, but also either
modify the security word or else not program the security word.
Part 8 General Purpose Input/Output (GPIO)
8.1 Introduction
This section is intended to supplement the GPIO information found in the 56F801X Peripheral Reference
Manual and contains only chip-specific information. This information supercedes the generic information
in the 56F801X Peripheral Reference Manual.
8.2 Configuration
There are four GPIO ports defined on the 56F8014. The width of each port, the associated peripheral and
reset functions are shown in Table 8-1. The specific mapping of GPIO port pins is shown in Table 8-2.
Table 8-1 GPIO Ports Configuration
GPIO Port
Available
Pins in
56F8014
Peripheral Function
Reset Function
A6
PWM, Reset
GPIO, except GPIOA7
B8
SPI, SCI, Timer
GPIO
C8
ADC
Analog
D4
JTAG
相關PDF資料
PDF描述
TCMD-05-S-06.00-01 CABLE ASSEM 2MM 10POS SGL END 6"
8532-09L INDUCTOR 4.7UH POWER SMD
LM4040BEX3-5.0+T IC VREF SHUNT PREC 5V SC-70-3
GBC13DRAN-S734 CONN EDGECARD 26POS .100 R/A SLD
LM4040BEX3-2.5+T IC VREF SHUNT PREC 2.5V SC-70-3
相關代理商/技術參數
參數描述
APMP100 功能描述:CHEMICAL METERING PUMP. 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
AP-MP3 制造商:Rogue Robotics 功能描述:uMP3 Playback Module 3-5 Volt MP3 PCM WAV Interface with PIC
APMR0016 功能描述:MOD APMR 3-PH VAULT DET DIN RAIL RoHS:否 類別:工業控制,儀表 >> 專用 系列:APMR 標準包裝:1 系列:PSE200 產品目錄頁面:2804 (CN2011-ZH PDF) 其它名稱:606-1016
APMR0086 制造商:Red Lion Controls 功能描述:SIGNAL CONDIT MOD, 3 PH FAULT DET 380V 制造商:Red Lion Controls 功能描述:3 PHASE FAULT DETECTOR 380VAC
APMR0096 制造商:Red Lion Controls 功能描述:Relay, Analog Phase Mod, 480 制造商:Red Lion Controls 功能描述:3 PHASE FAULT DETECTOR 480VAC