- 您現在的位置：買賣IC網 > PDF目錄166217 > AM79Q021VC (ADVANCED MICRO DEVICES INC) PCM CODEC, PQFP44 PDF資料下載
參數資料
| 型號： | AM79Q021VC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 編解碼器 |
| 英文描述： | PCM CODEC, PQFP44 |
| 封裝： | TQFP-44 |
| 文件頁數： | 33/64頁 |
| 文件大小： | 911K |
| 代理商： | AM79Q021VC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SLAC Products
39
MPI COMMAND STRUCTURE
This section details each MPI command. Each command is shown along with the format of any additional data bytes
that follow. For details of the filter coefficients of the form Cxymxy, refer to the General Description of CSD Coefficients
section on page 56.
Unused bits are indicated by “RSVD”; 0’s should be written to them, but 0’s are not guaranteed when they are read.
*Default field values are marked by an asterisk. A hardware reset forces the default values.
1.
Deactivate (Standby State)
MPI Command
(00h)
In the Deactivated mode:
All programmed information is retained.
The Microprocessor Interface (MPI) remains active.
The PCM inputs are disabled and the PCM outputs are high impedance unless
signaling on the PCM highway is programmed (SMODE = 1).
The analog output (VOUT) is disabled and biased at 2.1 V.
The channel status (CS) bit in the SLIC I/O Direction and Channel Status Register is
set to 0.
2.
Software Reset
MPI Command
(02h)
The action of this command is identical to that of the RST pin except that it only operates on the
channels selected by the Channel Enable Register and it does not change clock slots, time
slots, PCM highways, or global chip parameters. See the note under the hardware reset
command that follows.
3.
Hardware Reset
MPI Command
(04h)
Hardware reset is equivalent to pulling the RST on the device Low. This command does not
depend on the state of the Channel Enable Register.
Note: The action of a hardware reset is described in Reset States on page 31 of the section Operating
the QSLAC Device.
D7
D6
D5
D4
D3
D2
D1
D0
Command
0
D7
D6
D5
D4
D3
D2
D1
D0
Command
0
1
0
D7
D6
D5
D4
D3
D2
D1
D0
Command
0
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| AM79Q062JC | A/MU-LAW, PCM CODEC, PQCC32 |
| AM80A-048L-050P25 | 1-OUTPUT 125 W DC-DC REG PWR SUPPLY MODULE |
| AM8152BDC | SPECIALTY INTERFACE CIRCUIT, CDIP48 |
| AMB315218 | MOTION SENSOR, XSS |
| AMCY-ED12566/1 | 880 MHz - 915 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79Q02JC | 制造商:Advanced Micro Devices 功能描述: |
| AM79Q031 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Quad Subscriber Line Audio-Processing Circuit (QSLAC) Devices |
| AM79Q031JC | 制造商:Advanced Micro Devices 功能描述: |
| AM79Q061JC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM79Q061VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。