參數資料
型號： AM79Q021VC
廠商： ADVANCED MICRO DEVICES INC
元件分類： 編解碼器
英文描述： PCM CODEC, PQFP44
封裝： TQFP-44
文件頁數： 19/64頁
文件大小： 911K
代理商： AM79Q021VC
26
Am79Q02/021/031 Data Sheet
.
Figure 8. Clock Mode Option
E1 Multiplex Operation
The QSLAC device can multiplex input data from the
CD1 SLIC I/O pin into two separate status bits per
channel (CD1 and CD1B bits in the SLIC Input/Output
register, Commands 52/53h, and CDA and CDB bits in
the Real Time Data register, Commands 4D/4Fh)
using the E1 multiplex mode. This multiplex mode
provides the means to accommodate dual detect
states when connected to an AMD SLIC device, which
also supports ground-key detection in addition to loop
detect. AMD SLICs that support ground-key detect use
their E1 pin as an input to switch the SLIC’s single
detector (DET) output between internal loop detect or
gro und -key det ect com pa rato rs. Usin g t he E1
multiplex mode, a single QSLAC device can monitor
both loop detect and ground-key detect states of all
four connected SLICs without additional hardware.
Although normally used for ground key detect, this
multiplex function can also be used for monitoring
other signal states.
The E1 multiplex mode is selected by setting the EE1
bit (bit 7, Command C8/C9h) and CMODE bit (bit 4,
Command 46/47h) in the QSLAC device. The CMODE
bit must be selected (CMODE=1) for the master clock
to be derived from PCLK so that the MCLK/E1 pin can
be used as an output for the E1 signal. The multiplex
mode is then turned on by setting the EE1 bit. With the
E1 multiplex mode enabled, the QSLAC device
generates the E1 output signal. This signal is a
31.25
s (1/32 kHz) duration pulse occurring at a
4.923 kHz (64 kHz/13) rate. The polarity of this E1
output is selected by the E1P bit (bit 6, Command C8/
C9h) allowing this multiplex mode to accommodate all
SLICs regardless of their E1 high/low logic definition.
Figure 9 shows the SLIC Input/Output register, I/O
pins, E1 multiplex hardware operation for one QSLAC
device channel. It also shows the operation of the Real
Time Register. The QSLAC device E1 output signal
connects directly to the E1 inputs of all four connected
SLICs and is used by those SLICs to select an internal
comparator to route to the SLIC’s DET output. This E1
signal is also used internally by the QSLAC device for
controlling the multiplex operation and timing.
The CD1 and CD1B bits of the SLIC Input/Output
register are isolated from the CD1 pin by transparent
latches. When the E1 pulse is off, the CD1 pin data is
routed directly to the CD1 bit of the SLIC I/O register
and changes to the CD1B bit of that register are
disabled by its own latch. When E1 pulses on, the CD1
latch holds the last CD1 state in its register. At the
same time, the CD1B latch is enabled, which allows
CD1 pin data to be routed directly to the CD1B bit.
Time
Slot
Assigner
DSP
Engine
E1
Pulses
E1P
PCLK
MCLK/E1
N
÷
CSEL
CMODE
(= 1)
(= 0)
E1
(= 1)
(= 0)
EE1
Notes:
1. CMODE = Command 12, 13
Bit 4
2. CSEL = Command 12, 13
Bits 0–3
3. EE1 = Command 45, 46
Bit 7
4. E1P = Command 45, 46
Bit 6
(= 0)
(= 1)
相關PDF資料
PDF描述
AM79Q062JC A/MU-LAW, PCM CODEC, PQCC32
AM80A-048L-050P25 1-OUTPUT 125 W DC-DC REG PWR SUPPLY MODULE
AM8152BDC SPECIALTY INTERFACE CIRCUIT, CDIP48
AMB315218 MOTION SENSOR, XSS
AMCY-ED12566/1 880 MHz - 915 MHz RF/MICROWAVE DOUBLE BALANCED MIXER
相關代理商/技術參數
參數描述
AM79Q02JC 制造商:Advanced Micro Devices 功能描述:
AM79Q031 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Quad Subscriber Line Audio-Processing Circuit (QSLAC) Devices
AM79Q031JC 制造商:Advanced Micro Devices 功能描述:
AM79Q061JC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
AM79Q061VC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*