參數資料
型號: AM79C930VCW
廠商: ADVANCED MICRO DEVICES INC
元件分類: 微控制器/微處理器
英文描述: PCnet-Mobile Single-Chip Wireless LAN Media Access Controller
中文描述: 2 CHANNEL(S), LOCAL AREA NETWORK CONTROLLER, PQFP144
封裝: TQFP-144
文件頁數: 124/161頁
文件大?。?/td> 691K
代理商: AM79C930VCW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁當前第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
AMD
P R E L I M I N A R Y
124
Am79C930
PCMCIA CCR Registers and PCMCIA
CIS Space
Two bytes of attribute memory space have been
used by the Am79C930 device for storage of two card
configuration registers. These two registers are found
at attribute memory locations 800h and 802h. The
Configuration Option Register is located at Attribute
memory location 800h and the Card Configuration
and Status Register is located at Attribute memory
location 802h.
Because the location of these registers is fixed at 800h
and 802 in attribute memory space, then the value of the
CCR Offset located in the TPCC_RADR field of the Con-
figuration Tuple mustbe equal to 800h.
PCMCIA Configuration Option Register
This register is used to configure the Am79C930 device
and to issue a soft reset to the Am79C930 device.
The PCMCIA Configuration Option Register is located
at the fixed attribute memory location 0802h. Therefore,
the information programmed into the CIS must give the
value 2K (=0800h) as the Card Configuration Registers
Base Address in the TPCC_RADR field of the Configu-
ration Tuple. The Configuration Option Register is lo-
cated at TPCC_RADR + 2.
The following tables indicate the bits that are supported
in the Configuration Option Registers:
Bit
Name
Reset Value
Description
7
SRESET
0
Resets Am79C930 device. Setting this bit to 1 places the
Am79C930 device into the reset state, which is equivalent to the as-
sertion of the PCMCIA RESET signal. This bit does not reset itself
back to 0.
Level Mode Interrupts when LevelReq = 1. Pulse Mode Interrupts
when LevelReq = 0.
Configuration Index. This field is written with the index number of
the entry in the card’s Configuration Table which the system
chooses for this card. When Conf Index = “00000,” then the
Am79C930 device is in memory only mode. When any of these five
bits is set to 1, then the I/O interface is enabled, meaning that I/O
transfers are allowed.
6
LevelReq
0
5:0
Conf Index
0
PCMCIA Card Configuration and Status Register
This
card’s condition.
register
contains
information
about
the
The PCMCIA Card Configuration and Status Register is
located at the fixed attribute memory location 0802h.
Therefore, the information programmed into the CIS
must give the value 2K (=0800h) as the Card Configura-
tion Registers Base Address in the TPCC_RADR field of
the Configuration Tuple. The Card Configuration and
Status Register is located at TPCC_RADR + 2.
Bit
Name
Reset Value
Description
7:6
5
Reserved
IOIS8
0
Read only as a 0.
This bit is written by the host to indicate that the host is only capable
of 8-bit I/O accesses. This bit is ignored by the Am79C930 device,
since the Am79C930 device is only capable of 8-bit I/O accesses.
WAKEUP is used with the STSCHGFN bit of TCR15 to determine
the function of the
STSCHG
pin. When the STSCHGFN bit of
TCR15 is set to 1, then the WAKEUP bit is NANDed with the value
of the STSCHGD bit of MIR8 and the result is driven onto the
STSCHG
pin.
When the STSCHGFN bit of TCR15 is set to 0, then the STSCHG
pin becomes an output that is controlled by the STSCHGD bit
of MIR8.
Read/Write bit – serves no other function.
Requests the 80188 to enter power down mode. If already in power
down mode, this bit will indicate 1. When written with a 1, value read
will remain 0 until the device actually enters the power down mode.
4
Wakeup
0
3
2
Read-back
Power Down
0
0
相關PDF資料
PDF描述
AM79C940VCW Media Access Controller for Ethernet (MACE)
AM79C940 Media Access Controller for Ethernet (MACE)
AM79C940JCW Media Access Controller for Ethernet (MACE)
AM79C940KCW Media Access Controller for Ethernet (MACE)
AM79C960 PCnetTM-ISA Single-Chip Ethernet Controller
相關代理商/技術參數
參數描述
AM79C940 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Media Access Controller for Ethernet (MACE)
AM79C940_00 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Media Access Controller for Ethernet (MACE⑩)
AM79C940-16/25 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
AM79C940-16JC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C940-25JC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller