- 您現在的位置：買賣IC網 > PDF目錄366549 > AM79C873 (Advanced Micro Devices, Inc.) NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support PDF資料下載
參數資料
| 型號： | AM79C873 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| 中文描述： | NetPHY⑩-1 10/100 Mbps以太網物理層的單芯片收發器與100BASE - FX的支持 |
| 文件頁數： | 11/44頁 |
| 文件大小： | 543K |
| 代理商： | AM79C873 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Am79C873
11
P R E L I M I N A R Y
Clock Interface
OSCI/X1
Crystal or Oscillator Input
This pin should be connected to a 25 MHz (±50 ppm)
crystal if OSC/XTL=0 or a 25 MHz (±50 ppm) external
TTL oscillator input, if OSC/XTLB=1.
X2
Crystal Oscillator Output
An external 25 MHz (±50 ppm) crystal should be con-
nected to this pin if OSC/XTL=0, or left unconnected if
OSC/XTL=1.
OSC/XTL
Crystal or Oscillator Selector Pin
OSC/XTL=0: An external 25 MHz (±50ppm) crystal
should be connected to X1 and X2 pins.
OSC/XTL=1
:
An external 25 MHz (±50ppm) oscilla-
tor should be connected to X1 and X2 should be left
unconnected.
CLK25M
25 MHz Clock Output
This clock is derived directly from the crystal circuit.
PHY Address Interface
The PHYAD[4:0] pins provide up to 32 unique PHY
addresses. An address selection of all zeros (00000)
will result in a PHY isolation condition. See the isolate
bit description in the BMCR, address 00.
PHYAD0
PHY Address 0
This pin provides PHY address bit 0 for multiple PHY
address applications. The status of this pin is latched
into Register 17, bit 8 during power up/reset.
PHYAD1
PHY Address 1
This pin provides PHY address bit 1 for multiple PHY
address applications. The status of this pin is latched
into Register 17, bit 7 during power up/reset.
PHYAD2
PHY Address 2
This pin provides PHY address bit 2 for multiple PHY
address applications. The status of this pin is latched
into Register 17, bit 6 during power up/reset.
PHYAD3
PHY Address 3
This pin provides PHY address bit 3 for multiple PHY
address applications. The status of this pin is latched
into Register 17, bit 5 during power up/reset.
Input
Output
Output
I
Output/Z
Input
Input
Input
Input
PHYAD4
PHY Address 4
This pin provides PHY address bit 4 for multiple PHY
address applications. The status of this pin is latched
into Register 17, bit 4 during power up/reset.
Miscellaneous
NC
No Connect
These pins are to be left unconnected (floating).
BGREF
Bandgap Voltage Reference
Connect a 6.01K
, 1% resistor between this pin and
the BGRET pin to provide an accurate current refer-
ence for the NetPHY-1 device.
BGRET
Bandgap Voltage Reference Return
This is the return pin for 6.01K
resistor connection.
TRIDRV
Tri-State Digital Output
When set high, all digital output pins are set to a high
impedance state, and I/O pins, go to input mode.
RESET
Reset
This pin is the active low input that initializes the NetPHY-
1 device. It should remain low for 30 ms after VCC has
stabilized at 5 Vdc (nominal) before it transitions high.
TESTMODE
Test Mode Control Pin
TESTMODE=0: Normal operating mode.
Input
Input
Input
Input
Input
Input
TESTMODE=1: Enable test mode.
Power and Ground Pins
The power (VCC) and ground (GND) pins of the Net-
PHY-1 device are grouped in pairs of two categories -
Digital Circuitry Power/Ground Pairs and Analog Cir-
cuitry Power/Ground Pair.
DGND
Digital Logic Ground
These pins are the digital supply pairs.
DVCC
Digital Logic Power Supply
These pins are the digital supply pairs.
AGND
Analog Circuit Ground
These pins are the analog circuit supply pairs.
AVCC
Analog Circuit Power Supply
These pins are the analog circuit supply pairs.
Power
Power
Power
Power
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C873KCW | NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| AM79C874VI | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| Am79C874 | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C874VC | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C875 | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C873KCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| AM79C874 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C874KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C874VC | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
發布緊急采購，3分鐘左右您將得到回復。