- 您現在的位置：買賣IC網 > PDF目錄375306 > AM49BDS640AHD8I (SPANSION LLC) Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write PDF資料下載
參數資料
| 型號： | AM49BDS640AHD8I |
| 廠商： | SPANSION LLC |
| 元件分類： | 存儲器 |
| 英文描述： | Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA89 |
| 封裝： | 10 X 8 MM, FBGA-89 |
| 文件頁數： | 42/84頁 |
| 文件大小： | 763K |
| 代理商： | AM49BDS640AHD8I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
40
Am49BDS640AH
December 5, 2003
A D V A N C E I N F O R M A T I O N
RDY: Ready
The RDY is a dedicated output that, when the device is
configured in the Synchronous mode, indicates (when
at logic low) the system should wait 1 clock cycle before
expecting the next word of data. The RDY pin is only
controlled by CE#. Using the RDY Configuration
Command Sequence, RDY can be set so that a logic
low indicates the system should wait 2 clock cycles
before expecting valid data.
The following conditions cause the RDY output to be
low: during the initial access (in burst mode), and after
the boundary that occurs every 64 words beginning
with the 64th address, 3Fh.
When the device is configured in Asynchronous Mode,
the RDY is an open-drain output pin which indicates
whether an Embedded Algorithm is in progress or com-
pleted. The RDY status is valid after the rising edge of
the final WE# pulse in the command sequence.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the
Erase Suspend mode.) If the output is in high imped-
ance (Ready), the device is in the read mode, the
standby mode, or in the erase-suspend-read mode.
Table 17, “Write Operation Status,” on page 43
shows
the outputs for RDY.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address in the
same bank, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address
cause DQ6 to toggle. When the operation is complete,
DQ6 stops toggling.
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 toggles
for approximately 100 μs, then returns to reading array
data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are pro-
tected.
The system can use DQ6 and DQ2 together to deter-
mine whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing
(that is, the Embedded Erase algorithm is in progress),
DQ6 toggles. When the device enters the Erase
Suspend mode, DQ6 stops toggling. However, the
system must also use DQ2 to determine which sectors
are erasing or erase-suspended. Alternatively, the
system can use DQ7 (see the subsection on DQ7:
Data# Polling).
If a program address falls within a protected sector,
DQ6 toggles for approximately 1 ms after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded
Program algorithm is complete.
See the following for additional information:
Figure 7,
“Toggle Bit Algorithm,” on page 41
,
“DQ6: Toggle Bit I”
on page 40
,
Figure 38, “Toggle Bit Timings
(During Embedded Algorithm),” on page 67
(toggle bit
timing diagram), and
Table 16, “DQ6 and DQ2 Indica-
tions,” on page 42
.
Toggle Bit I on DQ6 requires either OE# or CE# to be
deasserteed and reasserted to show the change in
state.
相關PDF資料 |
PDF描述 |
|---|---|
| AM49BDS640AHD9I | Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49BDS640AHE8I | Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49BDS640AHE9I | Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49DL320BGT701 | Stacked Multi-Chip Package (MCP) Flash Memory and SRAM 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous |
| AM49DL320BGB701 | Stacked Multi-Chip Package (MCP) Flash Memory and SRAM 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM49BDS640AHD9I | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49BDS640AHE8I | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49BDS640AHE9I | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write |
| AM49DL3208G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Am49DL3208G - Stacked Multi-Chip Package (MCP) Flash Memory and pSRAM |
| AM49DL320BG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Am49DL320BG - Stacked Multi-Chip Package (MCP) Flash Memory and SRAM |
發布緊急采購，3分鐘左右您將得到回復。