- 您現在的位置：買賣IC網 > PDF目錄385090 > AK4184 (Asahi Kasei Microsystems Co.,Ltd) TSC with Keypad Scanner and GPIO Expander PDF資料下載
參數資料
| 型號： | AK4184 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | TSC with Keypad Scanner and GPIO Expander |
| 中文描述： | 臺糖與鍵盤掃描儀和GPIO擴展 |
| 文件頁數： | 4/36頁 |
| 文件大?。?/td> | 597K |
| 代理商： | AK4184 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
[AK4184]
MS0603-E-00
2007/04
4
PIN/FUNCTION
No.
A1
Pin Name
NC
I/O
-
Function
No Connection
No internal bonding. This pin should be open or connected to the ground.
Keypad Interrupt (Active Low)
This pin is “L” on a key press (when the AK4184 is allowed to detect a key press). This
pin is “H” after a debounce scan is completed. This is always “H” when the device is in
key interrupt disable state.
BUSY output
Keypad scanner: This pin stays “H” when the keypad scanner is on the debounce scan.
Touch Screen controller: This pin stays “H” from the end of sampling time to the timing
of the MSB data out.
Serial Data Output
Data is clocked at SCLK falling edge. DOUT pin is “L” when this part does not produce
data at the CSN=“L”. This pin is Hi-Z when CSN keeps “H”
Serial Data Input
Data is clocked on the rising edge of SCLK. Must keep “L” while not issuing command.
External Clock Input
Chip Select Input (Active Low)
Enables writing data to registers when CSN pin = “L”
Device Reset (Active Low)
Pen Interrupt Output (Active Low)
PENIRQN pin is “L” when touch-screen pressed is detected and the CSN pin is “H”.
This pin is “H” irrespective of touch screen press when pen interrupt is not enabled. The
state is dependent upon power down mode. See
Power-down control and
Pen
Interrupt for reference.
No Connection
No internal bonding. This pin should be open or connected to the ground.
Analog Ground
Touch Screen Y- plate Voltage Supply
Y axis measurement: Supplies voltage to the Y- position input
X axis measurement: OPEN state
Pen Pressure Measurement: This pin is the input for the A/D converter for Z2
measurement.
Pen Waiting State: connected to GND.
Touch Screen X- plate Voltage Supply
X axis measurement: Supplies voltage to the X- position input
Y axis measurement: OPEN state
Pen Pressure Measurement: Supplies the voltage to X- position input of the touch
panel
Pen Waiting State: OPEN state
Touch Screen Y+ plate Voltage Supply
X axis measurement: Supplies voltage to the X- position input
Y axis measurement: OPEN state
Pen Pressure measurement voltage supply
Pen Waiting State: OPEN state
Touch Screen X+ plate Voltage Supply
X axis measurement: Supplies voltage to the X+ position input
Y axis measurement: This pin is used for the input to the A/D converter
Pen Pressure measurement: This pin is the input for the A/D converter for Z1
measurement.
Pen Waiting State: Pulled up by an internal resistor (typ.50K
Ω
).
Analog Power Supply 2.5V ~ 3.6V
B1
KEYIRQN
O
C2
BUSY
O
C1
DOUT
O
D2
DIN
I
D1
E2
SCLK
CSN
I
I
E1
F2
RESETN
PENIRQN
I
O
G1
NC
-
F1
G2
VSS1
YN
-
I/O
F3
XN
I/O
G3
YP
I/O
F4
XP
I/O
G4
AVDD
-
相關PDF資料 |
PDF描述 |
|---|---|
| AK4184VG | TSC with Keypad Scanner and GPIO Expander |
| AK4220 | 7:3 Audio Switch and 6:3 Video Switch |
| AK4220VQ | 7:3 Audio Switch and 6:3 Video Switch |
| AK4250 | Output Coupling Capacitor-less Video Amp with LPF |
| AK4250VU | Output Coupling Capacitor-less Video Amp with LPF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4184A | 制造商:AKM 制造商全稱:AKM 功能描述:TSC with Keypad Scanner and GPIO Expander |
| AK4184AEG | 制造商:AKM 制造商全稱:AKM 功能描述:TSC with Keypad Scanner and GPIO Expander |
| AK4184VG | 制造商:AKM 制造商全稱:AKM 功能描述:TSC with Keypad Scanner and GPIO Expander |
| AK4185 | 制造商:AKM 制造商全稱:AKM 功能描述:Low Power Touch Screen Controller with SPI? Interface |
| AK4185_10 | 制造商:AKM 制造商全稱:AKM 功能描述:Low Power Touch Screen Controller with SPI? Interface |
發布緊急采購，3分鐘左右您將得到回復。