參數資料
型號： ADV7183BBSTZ
廠商： ANALOG DEVICES INC
元件分類： 顏色信號轉換
英文描述： Multiformat SDTV Video Decoder
中文描述： COLOR SIGNAL DECODER, PQFP80
封裝： LEAD FREE, MS-026-BEC, LQFP-80
文件頁數： 34/100頁
文件大?。?/td> 844K
代理商： ADV7183BBSTZ
ADV7183B
The chroma transient improvement block examines the input
video data. It detects transitions of chroma and can be
programmed to steepen the chroma edges in an attempt to
artificially restore lost color bandwidth. The CTI block,
however, operates only on edges above a certain threshold to
ensure that noise is not emphasized. Care has also been taken to
ensure that edge ringing and undesirable saturation or hue
distortion are avoided.
Rev. B | Page 34 of 100
Chroma transient improvements are needed primarily for
signals that experienced severe chroma bandwidth limitations.
For those types of signals, it is strongly recommended to enable
the CTI block via CTI_EN.
CTI_EN Chroma Transient Improvement Enable,
Address 0x4D[0]
The CTI_EN bit enables the CTI function. If set to 0, the CTI
block is inactive and the chroma transients are left untouched.
Setting CTI_EN to 0 disables the CTI block.
Setting CTI_EN to 1 (default) enables the CTI block.
CTI_AB_EN Chroma Transient Improvement Alpha
Blend Enable, Address 0x4D[1]
The CTI_AB_EN bit enables an alpha-blend function within
the CTI block. If set to 1, the alpha blender mixes the transient
improved chroma with the original signal. The sharpness of the
alpha blending can be configured via the CTI_AB[1:0] bits.
For the alpha blender to be active, the CTI block must be
enabled via the CTI_EN bit.
Setting CTI_AB_EN to 0 disables the CTI alpha blender.
Setting CTI_AB_EN to 1 (default) enables the CTI alpha-blend
mixing function.
CTI_AB[1:0] Chroma Transient Improvement Alpha
Blend, Address 0x4D[3:2]
The CTI_AB[1:0] controls the behavior of alpha-blend circuitry
that mixes the sharpened chroma signal with the original one. It
thereby controls the visual impact of CTI on the output data.
For CTI_AB[1:0] to become active, the CTI block must be
enabled via the CTI_EN bit, and the alpha blender must be
switched on via CTI_AB_EN.
Sharp blending maximizes the effect of CTI on the picture, but
can also increase the visual impact of small amplitude, high
frequency chroma noise.
Table 43. CTI_AB Function
CTI_AB[1:0]
00
Description
Sharpest mixing between sharpened and original
chroma signal
Sharp mixing
Smooth mixing
Smoothest alpha blend function
CTI_C_TH[7:0] CTI Chroma Threshold,
Address 0x4E[7:0]
The CTI_C_TH[7:0] value is an unsigned, 8-bit number speci-
fying how big the amplitude step in a chroma transition must be
steepened by the CTI block. Programming a small value into
this register causes even smaller edges to be steepened by the
CTI block. Making CTI_C_TH[7:0] a large value causes the
block to improve large transitions only.
01
10
11 (default)
The default value for CTI_C_TH[7:0] is 0x08, indicating the
threshold for the chroma edges prior to CTI.
DIGITAL NOISE REDUCTION (DNR)
Digital noise reduction is based on the assumption that high
frequency signals with low amplitude are probably noise and
that their removal, therefore, improves picture quality.
DNR_EN Digital Noise Reduction Enable,
Address 0x4D[5]
The DNR_EN bit enables or bypasses the DNR block.
Setting DNR_EN to 0 bypasses DNR (disables it).
Setting DNR_EN to 1 (default) enables digital noise reduction
on the luma data.
DNR_TH[7:0] DNR Noise Threshold, Address 0x50[7:0]
The DNR_TH[7:0] value is an unsigned 8-bit number used to
determine the maximum edge to be interpreted as noise and,
therefore, blanked from the luma data. Programming a large
value into DNR_TH[7:0] causes the DNR block to interpret
even large transients as noise and remove them. The effect on
the video data is, therefore, more visible.
Programming a small value causes only small transients to be
seen as noise and to be removed.
The recommended DNR_TH[7:0] setting for A/V inputs is
0x04, and the recommended DNR_TH[7:0] setting for tuner
inputs is 0x0A.
The default value for DNR_TH[7:0] is 0x08, indicating the
threshold for maximum luma edges to be interpreted as noise.
相關PDF資料
PDF描述
ADV7183BKSTZ Multiformat SDTV Video Decoder
ADV7183KST Advanced Video Decoder with 10-Bit ADC and Component Input Support
AD7183 Advanced Video Decoder with 10-Bit ADC and Component Input Support
ADV7185 Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
ADV7185KST Professional NTSC/PAL Video Decoder with 10-Bit CCIR656 Output
相關代理商/技術參數
參數描述
ADV7183BKST 制造商:Analog Devices 功能描述:MULTIFORMAT SDTV VID DECODER 80LQFP - Bulk
ADV7183BKSTZ 功能描述:IC VIDEO DECODER NTSC 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
ADV7183KST 制造商:Analog Devices 功能描述:Video Decoder 2ADC 10-Bit 80-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:VIDEO DECODER I.C. - Bulk
ADV7184 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder with Fast Switch Overlay Support
ADV7184BSTZ 功能描述:IC DECODER VID SDTV MULTI 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*