- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC836 (Analog Devices, Inc.) MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU PDF資料下載
參數資料
| 型號： | ADUC836 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 串行ADC |
| 英文描述： | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| 中文描述： | MicroConverter的，雙16位ADC的與嵌入62 kB閃存微控制器 |
| 文件頁數： | 58/80頁 |
| 文件大?。?/td> | 5913K |
| 代理商： | ADUC836 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
ADuC836
–58–
Mode 1: 8-Bit UART, Variable Baud Rate
Mode 1 is selected by clearing SM0 and setting SM1. Each data
byte (LSB first) is preceded by a start bit (0) and followed by a
stop bit (1). Therefore 10 bits are transmitted on TxD or received
on RxD. The baud rate can be set by Timer 1 or Timer 2 (or both).
Alternatively, a dedicated baud rate generator, Timer 3, is pro-
vided on-chip to generate high speed, very accurate baud rates.
Transmission is initiated by writing to SBUF. The “write to
SBUF” signal also loads a 1 (stop bit) into the ninth bit position
of the Transmit Shift Register. The data is output bit by bit until
the stop bit appears on TxD and the transmit interrupt flag (TI)
is automatically set, as shown in Figure 55.
TxD
TI
(SCON.1)
START
BIT
D0
D1
D2
D3
D4
D5
D6
D7
STOP BIT
SET INTERRUPT
i.e., READY FOR MORE
DATA
Figure 55. UART Serial Port Transmission, Mode 0
Reception is initiated when a 1-to-0 transition is detected on
RxD. Assuming a valid start bit was detected, character reception
continues. The start bit is skipped and the eight data bits are
clocked into the serial port shift register. When all eight bits have
been clocked in, the following events occur:
The eight bits in the Receive Shift Register are latched into
SBUF.
The ninth bit (stop bit) is clocked into RB8 in SCON.
The Receiver Interrupt flag (RI) is set.
If, and only if, the following conditions are met at the time, the
final shift pulse is generated:
RI = 0, and
Either SM2 = 0, or SM2 = 1 and the Received Stop Bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost and RI is not set.
Mode 2: 9-Bit UART with Fixed Baud Rate
Mode 2 is selected by setting SM0 and clearing SM1. In this mode,
the UART operates in 9-bit mode with a fixed baud rate. The baud
rate is fixed at Core_Clk/64 by default, although by setting the
SMOD bit in PCON, the frequency can be doubled to Core_Clk/32.
Eleven bits are transmitted or received, a start bit (0), eight data
bits, a programmable ninth bit, and a stop bit (1). The ninth bit
is most often used as a parity bit, although it can be used for any-
thing, including a ninth data bit if required.
*
f
CORE
refers to the output of the PLL as described in the On-Chip PLL section.
To transmit, the eight data bits must be written into SBUF. The
ninth bit must be written to TB8 in SCON. When transmission
is initiated, the eight data bits (from SBUF) are loaded onto the
transmit shift register (LSB first). The contents of TB8 are loaded
into the ninth bit position of the transmit shift register.
The transmission will start at the next valid baud rate clock. The
TI flag is set as soon as the stop bit appears on TxD.
Reception for Mode 2 is similar to that of Mode 1. The eight data
bytes are input at RxD (LSB first) and loaded onto the Receive
Shift Register. When all eight bits have been clocked in, the fol-
lowing events occur:
The eight bits in the Receive Shift Register are latched into
SBUF.
The ninth data bit is latched into RB8 in SCON.
The Receiver Interrupt flag (RI) is set.
If, and only if, the following conditions are met at the time the
final shift pulse is generated:
RI = 0, and
Either SM2 = 0, or SM2 = 1 and the received stop bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost and RI is not set.
Mode 3: 9-Bit UART with Variable Baud Rate
Mode 3 is selected by setting both SM0 and SM1. In this mode,
the 8051 UART serial port operates in 9-bit mode with a variable
baud rate determined by either Timer 1 or Timer 2. The operation
of the 9-bit UART is the same as for Mode 2, but the baud rate
can be varied as for Mode 1.
In all four modes, transmission is initiated by any instruction
that uses SBUF as a destination register. Reception is initiated in
Mode 0 by the condition RI = 0 and REN = 1. Reception is initi-
ated in the other modes by the incoming start bit if REN = 1.
UART Serial Port Baud Rate Generation
Mode 0 Baud Rate Generation
The baud rate in Mode 0 is fixed:
Mode 0
Baud Rate
f
CORE
12
=
*
Mode 2 Baud Rate Generation
The baud rate in Mode 2 depends on the value of the SMOD bit
in the PCON SFR. If SMOD = 0, the baud rate is 1/64 of the
core clock. If SMOD = 1, the baud rate is 1/32 of the core clock:
Mode 2
Baud Rate
f
CORE
SMOD
=
×
*
2
64
Mode 1 and 3 Baud Rate Generation
Traditionally, the baud rates in Modes 1 and 3 are determined by
the overflow rate in Timer 1 or Timer 2, or both (one for transmit
and the other for receive). On the ADuC836, however, the baud
rate can also be generated via a separate baud rate generator to
achieve higher baud rates and allow all three to be used for other
functions.
REV. A
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC836BCP | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836BS | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC842BCP62-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC843BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC842BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADUC836BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC836BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52 |
發布緊急采購，3分鐘左右您將得到回復。