參數資料
型號： ADUC836
廠商： Analog Devices, Inc.
元件分類： 串行ADC
英文描述： MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
中文描述： MicroConverter的，雙16位ADC的與嵌入62 kB閃存微控制器
文件頁數： 57/80頁
文件大?。?/td> 5913K
代理商： ADUC836
ADuC836
–57–
SCON UART Serial Port Control Registers
SFR Address 98H
Power-On Default Value 00H
Bit Addressable Yes
Table XXX. SCON SFR Bit Designations
Bit Name Description
7 SM0 UART Serial Mode Select Bits.
6 SM1 These bits select the Serial Port operating mode as follows:
SM0
SM1
0
0
0
1
1
0
1
1
5 SM2 Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3. In Mode 0, SM2 should be cleared. In Mode 1, if
SM2 is set, RI will not be activated if a valid stop bit was not received. If SM2 is cleared, RI will be set as soon
as the byte of data has been received. In Modes 2 or 3, if SM2 is set, RI will not be activated if the received ninth
data bit in RB8 is 0. If SM2 is cleared, RI will be set as soon as the byte of data has been received.
4 REN Serial Port Receive Enable Bit.
Set by user software to enable serial port reception.
Cleared by user software to disable serial port reception.
3 TB8 Serial Port Transmit (Bit 9).
The data loaded into TB8 will be the ninth data bit that will be transmitted in Modes 2 and 3.
2 RB8 Serial Port Receiver Bit 9.
The ninth data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8.
1 TI Serial Port Transmit Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or at the beginning of the stop bit in Modes 1, 2, and 3.
TI must be cleared by user software.
0 RI Serial Port Receive Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or halfway through the stop bit in Modes 1, 2, and 3.
RI must be cleared by software.
Selected Operating Mode
Mode 0: Shift Register, fixed baud rate (f
CORE
/12)
Mode 1: 8-bit UART, variable baud rate
Mode 2: 9-bit UART, fixed baud rate (f
CORE
/64) or (f
CORE
/32)
Mode 3: 9-bit UART, variable baud rate
UART SERIAL INTERFACE
The serial port is full-duplex, meaning it can transmit and receive
simultaneously. It is also receive-buffered, meaning it can com-
mence reception of a second byte before a previously received byte
has been read from the receive register. However, if the first byte
still has not been read by the time reception of the second byte is
complete, the first byte will be lost. The physical interface to the
serial data network is via pins RxD(P3.0) and TxD(P3.1), while
the SFR interface to the UART comprises the following registers:
SBUF
The serial port receive and transmit registers are both accessed
through the SBUF SFR (SFR address = 99H). Writing to SBUF
loads the transmit register, and reading SBUF accesses a physi-
cally separate receive register.
UART OPERATING MODES
Mode 0: 8-Bit Shift Register Mode
Mode 0 is selected by clearing both the SM0 and SM1 bits in
the SFR SCON. Serial data enters and exits through RxD. TxD
outputs the shift clock. Eight data bits are transmitted or received.
Transmission is initiated by any instruction that writes to SBUF.
The data is shifted out of the RxD line. The 8 bits are transmitted
with the least significant bit (LSB) first, as shown in Figure 54.
Reception is initiated when the Receive Enable bit (REN) is 1 and
the Receive Interrupt bit (RI) is 0. When RI is cleared, the data
is clocked into the RxD line and the clock pulses are output from
the TxD line.
CORE
CLK
ALE
RxD
(DATA OUT)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
S6
S5
S4
S3
S2
S1
S6
S5
S4
S4
S3
S2
S1
S6
S5
S4
S3
S2
S1
CYCLE 8
CYCLE 7
CYCLE 2
CYCLE 1
TxD
(SHIFT CLOCK)
Figure 54. UART Serial Port Transmission, Mode 0
REV. A
相關PDF資料
PDF描述
ADUC836BCP MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC836BS MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC842BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC836_02 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU
ADUC836BCP 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADUC836BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BS 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*