參數資料
型號: ADN2860ACPZ250-RL7
廠商: Analog Devices Inc
文件頁數: 5/20頁
文件大?。?/td> 0K
描述: IC POT DGTL 3CH 250K 24-LFCSP
標準包裝: 1
接片: 128,512,512
電阻(歐姆): 250k
電路數: 3
溫度系數: 標準值 35 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 2.7 V ~ 5.5 V,±2.25 V ~ 2.75 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 24-VFQFN 裸露焊盤,CSP
供應商設備封裝: 24-LFCSP-VQ(4x4)
包裝: 標準包裝
其它名稱: ADN2860ACPZ250RDKR
ADN2860
Rev. B | Page 13 of 20
Table 6. RDAC R/W EEPROM Addresses (CMD/ REG = 0, EE/RDAC = 1)
A4
A3
A2
A1
A0
Byte Description
0
RDAC0 8 LSBs
0
1
RDAC0 MSB
0
1
0
RDAC1 8 LSBs
0
1
RDAC1 MSB
0
1
0
RDAC2 7 bits
0
1
0
1
11 bytes RDAC user EEPROM
…to…
0
1
Table 7. RDAC Command Table (CMD/REG = 1)
C3
C2
C1
C0
Command Description
0
NOP.
0
1
Restore EEPROM to RDAC.1
0
1
0
Store RDAC to EEPROM.2
0
1
Decrement RDAC 6 dB.
0
1
0
Decrement all RDACs 6 dB.
0
1
0
1
Decrement RDAC one step.
0
1
0
Decrement all RDACs one step.
0
1
Reset. Restore EEPROM to all RDACs.2
1
0
Increment RDAC 6 dB.
1
0
1
Increment all RDACs 6 dB.
1
0
1
0
Increment RDAC one step.
1
0
1
Increment all RDACs one step.
1
0
Reserved.
…to…
1
1 Command leaves the device in the EEPROM read power state. Issue the NOP command to return the device to the idle state.
2 Command requires acknowledge polling after execution.
RDAC Interface Operation
Each programmable resistor wiper setting is controlled by
specific RDAC registers, as shown in Table 5. Each RDAC
register corresponds to an EEPROM memory location, which
provides nonvolatile wiper storage functionality.
RDAC registers and their corresponding EEPROM memory
locations are programmed and read independently from each
other. The RDAC register is refreshed by the EEPROM locations,
either with a hardware reset via Pin 1, or by issuing one of the
various RDAC register load commands shown in the Table 7.
RDAC Write
Setting the wiper position requires an RDAC write operation,
shown in Figure 22. RDAC write operations follow a format
similar to the EEPROM write interface. The only difference
between an RDAC write and an EEPROM write operation is the
use of an RDAC address byte in place of the memory address
used in the EEPROM write operation. The RDAC address byte
is described in detail in Table 5 and Table 6.
As with the EEPROM write operation, any RDAC EEPROM
(Shortcut Command 2) write operation disables the I2C
interface during the internal write cycle. Acknowledge polling,
as described in the EEPROM Interface section, is required to
determine whether the write cycle is complete.
RDAC Read
The ADN2860 provides two RDAC read operations. The first,
shown in Figure 23, reads the contents of the current RDAC
address counter. Figure 24 illustrates the second read operation,
which allows users to specify which RDAC register to read by
first issuing a dummy write command to change the RDAC
address pointer, and then proceeding with the RDAC read
operation at the new address location.
The read-only RDAC EEPROM memory locations can also be
read by using the address and bits specified in Table 6.
相關PDF資料
PDF描述
ADN4600ACPZ IC CROSSPOINT SWITCH 8X8 64LFCSP
ADN4604ASVZ-RL IC CROSSPOINT SWIT 16X16 100TQFP
ADN4605ABPZ IC CROSSPOINT SWITCH 352BGA
ADN4661BRZ-REEL7 IC DRIVER DIFF LVDS 1CH 8SOIC
ADN4662BRZ-REEL7 IC RCVR DIFF LVDS 1CH 8SOIC
相關代理商/技術參數
參數描述
ADN2860ACPZ25-RL7 功能描述:IC POT DGTL 3CH 25K 24-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:2,500 系列:XDCP™ 接片:256 電阻(歐姆):100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C(設備位址) 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR)
ADN2860-EVAL 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel Digital Potentiometer with Nonvolatile Memory
ADN2865 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 12.3Mb/s to 2.7Gb/s Clock and Data Recovery IC w/Loop Timed SERDES
ADN2865ACP 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 12.3Mb/s to 2.7Gb/s Clock and Data Recovery IC w/Loop Timed SERDES
ADN2865ACP-RL 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 12.3Mb/s to 2.7Gb/s Clock and Data Recovery IC w/Loop Timed SERDES