參數資料
型號: ADM1069AST
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP32
封裝: MS-026-BBA, LQFP-32
文件頁數: 4/36頁
文件大?。?/td> 763K
代理商: ADM1069AST
ADM1069
Rev. A | Page 12 of 36
POWERING THE ADM1069
The ADM1069 is powered from the highest voltage input on
either the positive-only supply inputs (VPn) or the high voltage
supply input (VH). This technique offers improved redundancy
because the device is not dependent on any particular voltage
rail to keep it operational. The same pins are used for supply
fault detection (discussed later in the Supply Supervision
section). A VDD arbitrator on the device chooses which supply
to use. The arbitrator can be considered an OR’ing of four
LDOs together. A supply comparator chooses the highest input
to provide the on-chip supply. There is minimal switching loss
with this architecture (~0.2 V), resulting in the ability to power
the ADM1069 from a supply as low as 3.0 V. Note that the
supply on the VXn pins cannot be used to power the device.
An external capacitor to GND is required to decouple the on-
chip supply from noise. This capacitor should be connected to
the VDDCAP pin, as shown in Figure 20. The capacitor has
another use during brownouts (momentary loss of power).
Under these conditions, when the input supply (VPn or VH)
dips transiently below VDD, the synchronous rectifier switch
immediately turns off so that it does not pull VDD down. The
VDD capacitor can then act as a reservoir to keep the device
active until the next highest supply takes over the powering of
the device. A 10 μF capacitor is recommended for this
reservoir/decoupling function.
When two or more supplies are within 100 mV of each other,
the supply that first takes control of VDD keeps control. For
example, if VP1 is connected to a 3.3 V supply, VDD powers up
to approximately 3.1 V through VP1. If VP2 is then connected
to another 3.3 V supply, VP1 still powers the device unless VP2
goes 100 mV higher than VP1.
SUPPLY
COMPARATOR
IN
EN
OUT
4.75V
LDO
IN
EN
OUT
4.75V
LDO
IN
EN
OUT
4.75V
LDO
IN
EN
OUT
4.75V
LDO
VH
VP3
VP2
VP1
VDDCAP
INTERNAL
DEVICE
SUPPLY
04735-022
Figure 20. VDD Arbitrator Operation
相關PDF資料
PDF描述
ADM231LAN 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ADM231LAQ 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ADM231LAR 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ADM232A 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ADM2486BRW IC QUAD OPTO-ISOLATOR ILQ2
相關代理商/技術參數
參數描述
ADM1069AST-REEL 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 32-Pin LQFP T/R
ADM1069AST-REEL7 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 32-Pin LQFP T/R
ADM1069ASTZ 功能描述:IC SUPERVISOR/SEQUENCER 32-LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V,2.955V,可調,可調,可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6
ADM1069ASTZ-REEL 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP(0.059",1.50mm 寬)5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT
ADM1069ASTZ-REEL7 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V,2.955V,可調,可調,可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6