- 您現在的位置：買賣IC網 > PDF目錄165349 > ADM1033ARQ-REEL (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADM1033ARQ-REEL |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 14/39頁 |
| 文件大?。?/td> | 819K |
| 代理商： | ADM1033ARQ-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
ADM1033
Rev. 0 | Page 21 of 40
Table 16. Status Register 1 (Reg. 0x4F)
Bit No.
Name
Description
7
LH
1 = Local high temperature limit has been
exceeded.
6
LL
1 = Local low temperature limit has been
exceeded.
5
RH
1= Remote high temperature limit has
been exceeded.
4
RL
1 = Remote low temperature limit has
been exceeded.
3
RD
1 = Remote diode error; indicates an
open or short on the D1+/D1 pins.
2
Unused
Reserved.
1
Unused
Reserved.
0
Unused
Reserved.
Table 17. Status Register 2 (Reg. 0x50)
Bit No.
Name
Description
7
LT
1 = Local THERM temperature limit has
been exceeded.
6
RT
1 = Remote THERM temperature limit has
been exceeded.
5
Unused
Reserved.
4
T%
1 = THERM timer limit has been
exceeded.
3
TA
1 = One of the THERM limits has been
exceeded; and the THERM output signal
has been asserted.
2
TS
1 = THERM pin is active. Clears on a read,
if THERM is not active.
1
Res
Reserved.
0
Res
Reserved.
Table 18. Status Register 3 (Reg. 0x51)
Bit No.
Name
Description
7
FS
1= Fan has stalled.
6
FA
1= Fan ALARM speed, indicates fan is
running at alarm speed.
5
Res
Reserved.
4
Res
Reserved.
3
Res
Reserved.
2
Res
Reserved.
1
Res
Reserved.
0
ALERT
1= SMBusALERT low, indicates the
ADM1033 has pulled the SMBusALERT
line low.
ALERT INTERRUPT BEHAVIOR
The ADM1033 generates an ALERT to signal out-of-limit
conditions. Out-of-limit conditions can also be detected by
polling the status registers. The ADM1033 has two ALERT
outputs, called ALERT Comp and SMBusALERT.
In SMBusALERT mode, the output remains low until the
following combination of conditions occur: the measurement
falls back within its programmed limits, and either the status
register is read or an ARA is completed.
In ALERT Comp mode, the output automatically resets
once the temperature measurement falls back within the
programmed limits.
For the SMBusALERT output, a status bit is set when a
measurement goes outside its programmed limit. If the
corresponding mask bit is not set, the SMBusALERT output
is pulled low. If the measured value falls back within the limits,
the SMBusALERT output remains low until the corresponding
status register is read or until an ARA is completed, as long as
no other measurement is outside its limits.
On the other hand, the ALERT Comp output is automatically
pulled low when a measurement goes outside its programmed
limits. Once the measurement falls back within its limits, the
ALERT output is automatically pulled back high again,
assuming no other measurement channel is outside its limits.
The main difference between the two outputs is that the
SMBusALERT does not reset without software intervention,
while the ALERT Comp output automatically resets itself. Note:
In this data sheet, an ALERT refers to both the ALERT Comp
and SMBusALERT, unless otherwise stated.
ALERT, 70 C
TEMPERATURE
LIMITS
TIME
CLEARED
ON READ
ALERT COMP
SMBusALERT
04937-0-029
Figure 31. How ALERT Comparator and SMBusALERT Outputs Work
Rev. 1 | Page 21 of 39 | www.onsemi.com
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1069AST | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP32 |
| ADM231LAN | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM231LAQ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM231LAR | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ADM232A | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1033ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 +/- 1 C Digital 2-Wire RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1033ARQZ-REEL | 功能描述:板上安裝溫度傳感器 +/- 1 C Digital 2-Wire RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1033ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。