multiplexer/demultiplex" />
參數資料
型號： ADG796ABCPZ-REEL
廠商： Analog Devices Inc
文件頁數： 9/24頁
文件大小： 0K
描述： IC MUX/DEMUX HEX 2X1 24LFCSP
產品變化通告： ADG79xx Discontinuance Notice 17/Aug/2010
標準包裝： 1
功能： 多路復用器/多路分解器
電路： 6 x 2:1
導通狀態電阻： 4 歐姆
電壓電源： 單電源
電壓 - 電源，單路/雙路(±)： 3V，5V
電流 - 電源： 1nA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-VFQFN 裸露焊盤，CSP
供應商設備封裝： 24-LFCSP-VQ（4x4）
包裝： 標準包裝
產品目錄頁面： 801 (CN2011-ZH PDF)
其它名稱： ADG796ABCPZ-REELDKR
ADG796A
Rev. 0 | Page 17 of 24
THEORY OF OPERATION
The ADG796A is a monolithic CMOS device comprising six 2:1
multiplexer/demultiplexers controllable via a standard I2C serial
interface. The CMOS process provides ultralow power
dissipation, yet offers high switching speed and low on resistance.
The on resistance profile is very flat over the full analog input
range, and wide bandwidth ensures excellent linearity and low
distortion. These features, combined with a wide input signal
range, make the ADG796A the ideal switching solution for a
wide range of TV applications.
The switches conduct equally well in both directions when on.
In the off condition, signal levels up to the supplies are blocked.
The integrated serial I2C interface controls the operation of the
multiplexers.
The ADG796A has many attractive features, such as the ability
to individually control each multiplexer and the option of
reading back the status of any switch through the I2C interface.
The following sections describe these features in more detail.
I2C SERIAL INTERFACE
The ADG796A is controlled via an I2C-compatible serial bus
interface (refer to the I2C-Bus Specification available from
Philips Semiconductor) that allows the part to operate as a slave
device (no clock is generated by the ADG796A). The communi-
cation protocol between the I2C master and the device operates
as follows:
1.
The master initiates data transfer by establishing a start
condition defined as a high-to-low transition on the SDA
line while SCL is high. This indicates that an address/data
stream follows. All slave devices connected to the bus
respond to the start condition and shift in the next eight
bits, consisting of a seven bit address (MSB first) plus an
R/W bit. This bit determines the direction of the data flow
during the communication between the master and the
addressed slave device.
2.
The slave device whose address corresponds to the
transmitted address responds by pulling the SDA line low
during the ninth clock pulse (this is called the acknowledge
bit). At this stage, all other devices on the bus remain idle
while the selected device waits for data to be written to, or
read from, its serial register. If the R/W bit is set high, the
master reads from the slave device. However, if the R/W bit
is set low, the master writes to the slave device.
3.
Data transmits over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge
bit). The transitions on the SDA line must occur during the
low period of the clock signal (SCL) and remain stable
during the high period (SCL). This is because a low-to-
high transition when the clock signal is high can be
interpreted as a stop event, which ends the communication
between the master and the addressed slave device.
4.
After transferring all data bytes, the master establishes a
stop condition, defined as a low-to-high transition on the
SDA line while SCL is high. In write mode, the master pulls
the SDA line high during the 10th clock pulse to establish a
stop condition. In read mode, the master issues a no
acknowledge for the ninth clock pulse (the SDA line
remains high). The master then brings the SDA line low
before the 10th clock pulse, and then high during the 10th
clock pulse to establish a stop condition.
I2C ADDRESS
The ADG796A has a seven-bit I2C address. The five most
significant bits are internally hardwired while the last two bits,
A0 and A1, are user adjustable. This allows the user to connect
up to four ADG796As to the same bus. The I2C bit map shows
the configuration of the seven-bit address.
Seven-Bit I2C Address Bit Configuration
MSB
LSB
1
0
1
0
A1
A0
WRITE OPERATION
When writing to the ADG796A, the user must begin with an
address byte and R/W bit. Next, the switch acknowledges that it
is prepared to receive data by pulling SDA low. Data is loaded
into the device as a 16-bit word under the control of a serial clock
input, SCL. Figure 27 illustrates the entire write sequence for
the ADG796A. The first data byte (AX7 to AX0) controls the
status of the switches, while the LDSW and RESETB bits from
the second byte control the operation mode of the device.
SCL
SDA
A1
A0
AX6
AX7
R/W
AX5 AX4 AX3 AX2 AX1 AX0
X
RESETB
LDSW
START
CONDITION
BY MASTER
STOP
CONDITION
BY MASTER
ADDRESS BYTE
ACKNOWLEDGE
BY SWITCH
ACKNOWLEDGE
BY SWITCH
ACKNOWLEDGE
BY SWITCH
06
03
6
-01
4
NOTES
1. X = LOGIC STATE DOES NOT MATTER.
Figure 27. Write Operation
相關PDF資料
PDF描述
ADG799GBCPZ-REEL IC CROSSPOINT SWIT TRPL 24LFCSP
ADG802BRT-REEL7 IC SWITCH SPST SOT23-6
ADG804YRM IC MULTIPLEXER 4X1 10MSOP
ADG813YRU IC SWITCH QUAD SPST 16TSSOP
ADG819BRM IC SWITCH SPDT 8MSOP
相關代理商/技術參數
參數描述
ADG796ACCPZ-500RL7 制造商:AD 制造商全稱:Analog Devices 功能描述:I2C-Compatible, Wide Bandwidth, Hex 2:1 Multiplexer
ADG796ACCPZ-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:I2C-Compatible, Wide Bandwidth, Hex 2:1 Multiplexer
ADG798HFRZ 功能描述:1 Circuit IC Switch 8:1 10 Ohm 16-CFlatPack 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:在售 開關電路:- 多路復用器/解復用器電路:8:1 電路數:1 導通電阻（最大值）:10 歐姆 通道至通道匹配（ΔRon）:1.25 歐姆 電壓 -?電源，單（V+）:3 V ~ 5.5 V 電壓 - 電源，雙（V±）:±2.5V 開關時間（Ton, Tof）（最大值）:30ns，20ns -3db 帶寬:55MHz 電荷注入:3pC 溝道電容 （CS(off），CD（off））:13pF，85pF 電流 - 漏泄（IS（off））（最大值）:180nA 串?dāng)_:-60dB @ 10MHz 工作溫度:-55°C ~ 210°C（TA） 封裝/外殼:16-CFlatPack 供應商器件封裝:16-CFlatPack 標準包裝:1
ADG798HFZ 功能描述:1 Circuit IC Switch 8:1 10 Ohm 16-CFlatPack 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:在售 開關電路:- 多路復用器/解復用器電路:8:1 電路數:1 導通電阻（最大值）:10 歐姆 通道至通道匹配（ΔRon）:1.25 歐姆 電壓 -?電源，單（V+）:3 V ~ 5.5 V 電壓 - 電源，雙（V±）:±2.5V 開關時間（Ton, Tof）（最大值）:30ns，20ns -3db 帶寬:55MHz 電荷注入:3pC 溝道電容 （CS(off），CD（off））:13pF，85pF 電流 - 漏泄（IS（off））（最大值）:180nA 串?dāng)_:-60dB @ 10MHz 工作溫度:-55°C ~ 210°C（TA） 封裝/外殼:16-CFlatPack 供應商器件封裝:16-CFlatPack 標準包裝:1
ADG799A 制造商:AD 制造商全稱:Analog Devices 功能描述:IC-Compatible, Wide Bandwidth, Triple 2 】 2 Crosspoint Switch
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*