參數資料
型號: ADC1112D125HN
廠商: NXP Semiconductors N.V.
元件分類: 外設及接口
英文描述: Dual 11-bit ADC; CMOS or LVDS DDR digital outputs
封裝: ADC1112D125HN/C1<SOT804-3|<<<1<Always Pb-free,;ADC1112D125HN/C1<SOT804-3|<<<1<Always Pb-free,;
文件頁數: 28/41頁
文件大?。?/td> 565K
代理商: ADC1112D125HN
ADC1112D125
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 3 March 2011
28 of 41
NXP Semiconductors
ADC1112D125
Dual 11-bit ADC: CMOS or LVDS DDR digital outputs
Table 17.
[1]
Bit R/W indicates whether it is a read (logic 1) or a write (logic 0) operation.
[2]
Bits W1 and W0 indicate the number of bytes to be transferred (see
Table 18
).
Table 18.
W1
0
0
1
1
Bits A12 to A0 indicate the address of the register being accessed. In the case of a
multiple byte transfer, this address is the first register to be accessed. An address counter
is increased to access subsequent addresses.
The steps involved in a data transfer are as follows:
1. A falling edge on pin CS in combination with a rising edge on pin SCLK determine the
start of communications.
2. The first phase is the transfer of the 2-byte instruction.
3. The second phase is the transfer of the data which can vary in length but is always a
multiple of 8 bits. The MSB is always sent first (for instruction and data bytes).
4. A rising edge on pin CS indicates the end of data transmission.
11.6.2
Default modes at start-up
During circuit initialization it does not matter which output data standard has been
selected. At power-up, the device enters Pin control mode.
A falling edge on pin CS triggers a transition to SPI control mode. When the
ADC1112D125 enters SPI control mode, the output data standard (CMOS/LVDS DDR) is
determined by the level on pin SDIO (see
Figure 33
). Once in SPI control mode, the
output data standard can be changed via bit LVDS_CMOS
(see
Table 24
).
Instruction bytes for the SPI
MSB
7
R/W
[1]
A7
LSB
0
A8
A0
Bit
Description
6
W1
[2]
A6
5
W0
[2]
A5
4
A12
A4
3
A11
A3
2
A10
A2
1
A9
A1
Number of data bytes to be transferred after the instruction bytes
W0
Number of bytes transferred
0
1 byte
1
2 bytes
0
3 bytes
1
4 bytes or more
Fig 32. SPI mode timing
CS
SCLK
SDIO
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D3
D2
D1
D0
D0
D7
D6
D5
D4
Instruction bytes
Register N (data)
Register N + 1 (data)
005aaa086
相關PDF資料
PDF描述
ADC1115S125HN Single 11-bit ADC 125 Msps with Input Buffer CMOS or LVDS DDR digital outputs
ADC1115S125HN Single 11-bit ADC 125 Msps with Input Buffer CMOS or LVDS DDR digital outputs
ADC1206S040H Single 12 bits ADC up to 40 Msps
ADC1206S040H Single 12 bits ADC up to 40 Msps
ADC1206S055H Single 12 bits ADC up to 55 Msps
相關代理商/技術參數
參數描述
ADC1112D125HN/C1,5 功能描述:模數轉換器 - ADC 2IN 125MSPS 66.2dB RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC1112D125HN/C1+551 制造商:NXP Semiconductors 功能描述:Bulk 制造商:NXP Semiconductors 功能描述:0
ADC1112D125HN-C1 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC1112D125HN-C18 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32