- 您現在的位置：買賣IC網 > PDF目錄16426 > AD9980/PCBZ (Analog Devices Inc)KIT EVALUATION AD9980 PDF資料下載
參數資料
| 型號： | AD9980/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/44頁 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION AD9980 |
| 標準包裝： | 1 |
| 系列： | Advantiv® |
| 主要目的： | 視頻，視頻處理 |
| 已用 IC / 零件： | AD9980 |
| 已供物品： | 板 |
| 相關產品： | AD9980KSTZ-95-ND - IC INTERFACE 8BIT ANALOG 80LQFP AD9980KSTZ-80-ND - IC INTERFACE 8BIT ANALOG 80LQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9980
Rev. 0 | Page 31 of 44
0x14
4
Input Vsync Polarity
If Bit 5 of Register 0x14 is 1, the value of this bit
specifies the polarity of the input Vsync. Setting this
bit to 0 indicates an active low Vsync; setting this bit to
1 indicates an active high Vsync. Power-up default is 1.
Table 24. Vsync Input Polarity Settings
Override Bit
Result
0
Vsync input polarity is negative
1
Vsync input polarity is positive
0x14
3
Vsync Output Polarity
This bit sets the polarity of the Hsync output. Setting
this bit to 0 sets the Hsync output to active low. Setting
this bit to 1 sets the Hsync output to active high.
Power-up default is 1.
Table 25. Vsync Output Polarity Settings
Vsync Output
Polarity Bit
Result
0
Vsync output polarity is negative
1
Vsync output polarity is positive
0x14
2
Vsync Filter Enable
This bit enables the Vsync filter allowing precise
placement of the Vsync with respect to the Hsync
and facilitating the correct operation of the
Hsyncs/Vsync count.
Table 26. Vsync Filter Enable
Vsync Filter Bit
Result
0
Vsync filter disabled
1
Vsync filter enabled
0x14
1
Vsync Duration Enable
This enables the Vsync duration block, which is
designed to be used with the Vsync filter. Setting the
bit to 0 leaves the Vsync output duration unchanged.
Setting the bit to 1 sets the Vsync output duration
based on Register 0x15. Power-up duration is 0.
Table 27. Vsync Duration Enable
Vsync
Duration Bit
Result
0
Vsync output duration is unchanged
1
Vsync output duration is set by Register 0x15
0x15
7:0
Vsync Duration
This is used to set the output duration of the Vsync,
and is designed to be used with the Vsync filter. This is
valid only if Register 0x14, Bit 1 is set to 1. Power-up
default is 10.
COAST AND CLAMP CONTROLS
0x16
7:0
Precoast
This register allows the internally generated Coast
signal to be applied prior to the Vsync signal. This is
necessary in cases where pre-equalization pulses are
present. The step size for this control is one Hsync
period. For Precoast to work correctly, it is necessary
for the Vsync filter (Register 0x14, Bit 2) and sync
processing filter (Register 0x20, Bit 1) both to be either
enabled or disabled. The power-up default is 00.
0x17
7:0
Postcoast
This register allows the internally generated Coast
signal to be applied following the Vsync signal. This is
necessary in cases where post equalization pulses are
present. The step size for this control is one Hsync
period. For Postcoast to work correctly, it is necessary
for the Vsync filter (Register 0x14, Bit 2) and sync
processing filter (Register 0x20, Bit 1) both to be either
enabled or disabled. The power-up default is 00.
0x18
7
Coast Source
This bit is used to select the active Coast source. The
choices are the COAST input pin or Vsync. If Vsync is
selected, the additional decision of using the Vsync
input pin or the output from the sync separator needs
to be made (Register 0x14, Bits [7: 6]).
Table 28. Coast Source Selection Settings
Select
Result
0
Vsync (internal Coast)
1
COAST input pin
0x18
6
Coast Polarity Override
This register is used to override the internal circuitry
that determines the polarity of the Coast signal going
into the PLL. The power-up default setting is 0.
Table 29. Coast Polarity Override Settings
Override Bit
Result
0
Coast polarity determined by chip
1
Coast polarity determined by user
0x18
5
Input Coast Polarity
This register sets the input Coast polarity when Bit 6
of Register 0x18 = 1. The power-up default setting is 1.
Table 30. Coast Polarity Settings
Coast Polarity
Bit
Result
0
Coast polarity is negative
1
Coast polarity is positive
相關PDF資料 |
PDF描述 |
|---|---|
| 073170-000 | SHIELD TERMINATOR |
| VI-J4B-EX | CONVERTER MOD DC/DC 95V 75W |
| AD9880/PCBZ | KIT EVALUATION AD9880 |
| S01-02-R | SOLDER SLEEVE IMMERS RESIS .650" |
| ILSB1206ER180K | INDUCTOR 18UH 10% 1206 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9981 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9981/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9981/PCBZ | 制造商:Analog Devices 功能描述:Evaluation Board For The High Performance 10-Bit Display Interface 制造商:Analog Devices 功能描述:EVAL BD FOR THE HI-PERF 10-BIT DISPLAY INTRFC - Bulk |
| AD9981KST-80 | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE 10-BIT DISPLAY INTERFACE - Bulk |
| AD9981KSTZ-80 | 功能描述:IC INTERFACE 10BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
發布緊急采購，3分鐘左右您將得到回復。