- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9634BCPZRL7-170 (Analog Devices Inc)IC ADC 12BIT SRL 170MSPS 32LFCSP PDF資料下載
參數資料
| 型號： | AD9634BCPZRL7-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SRL 170MSPS 32LFCSP |
| 標準包裝： | 1,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 170M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 340mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-WQ（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 單端，1 個差分 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9634
Rev. 0 | Page 19 of 32
THEORY OF OPERATION
250 MHz using appropriate low-pass or band-pass filtering at
the ADC inputs with little loss in ADC performance.
Programming and control of the AD9634 are accomplished
using a 3-pin, SPI-compatible serial interface.
ADC ARCHITECTURE
The AD9634 architecture consists of a front-end sample-and-
hold circuit, followed by a pipelined, switched-capacitor ADC.
The quantized outputs from each stage are combined into a
final 12-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample and the remaining stages to operate on the preceding
samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digital-
to-analog converter (DAC) and an interstage residue amplifier
(MDAC). The MDAC magnifies the difference between the
reconstructed DAC output and the flash input for the next stage
in the pipeline. One bit of redundancy is used in each stage to
facilitate digital correction of flash errors. The last stage simply
consists of a flash ADC.
The input stage contains a differential sampling circuit that can
be ac- or dc-coupled in differential or single-ended modes. The
output staging block aligns the data, corrects errors, and passes the
data to the output buffers. The output buffers are powered from a
separate supply, allowing digital output noise to be separated from
the analog core. During power-down, the output buffers go into
a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9634 is a differential switched-capacitor
circuit that has been designed to attain optimum performance
when processing a differential input signal.
The clock signal alternatively switches the input between sample
mode and hold mode (see the configuration shown in Figure 46).
When the input is switched into sample mode, the signal source
must be capable of charging the sampling capacitors and settling
within clock cycle.
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
In intermediate frequency (IF) undersampling applications, reduce
the shunt capacitors. In combination with the driving source
impedance, the shunt capacitors limit the input bandwidth.
Refer to the AN-742 Application Note, Frequency Domain
Response of Switched-Capacitor ADCs; the AN-827 Application
Note, A Resonant Approach to Interfacing Amplifiers to Switched-
Capacitor ADCs; and the Analog Dialogue article, “Transformer-
information on this subject.
CPAR1
CPAR2
S
CFB
CS
BIAS
VIN+
H
VIN–
09
996-
043
Figure 46. Switched-Capacitor Input
For best dynamic performance, match the source impedances
driving VIN+ and VIN and differentially balance the inputs.
Input Common Mode
The analog inputs of the AD9634 are not internally dc biased. In
ac-coupled applications, the user must provide this bias externally.
Setting the device so that VCM = 0.5 × AVDD (or 0.9 V) is
recommended for optimum performance. An on-board common-
mode voltage reference is included in the design and is available
from the VCM pin. Using the VCM output to set the input
common mode is recommended. Optimum performance is
achieved when the common-mode voltage of the analog input
is set by the VCM pin voltage (typically 0.5 × AVDD). The
VCM pin must be decoupled to ground by a 0.1 μF capacitor,
as described in the Applications Information section. Place this
decoupling capacitor close to the pin to minimize the series
resistance and inductance between the part and this capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9637BCPZRL7-80 | IC ADC 12BIT SRL 80MSPS 64LFCSP |
| AD9639BCPZ-170 | IC ADC 12B 170MSPS QUAD 72LFCSP |
| AD9640ABCPZ-125 | IC ADC 14BIT 125MSPS 64LFCSP |
| AD9641BCPZ-80 | IC ADC 14BIT SRL 80MSPS 32LFCSP |
| AD9644BCPZ-80 | IC ADC 14BIT 80MSPS 3V 48LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9634BCPZRL7-210 | 功能描述:模數轉換器 - ADC 12 Bit 210 Msps ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9634BCPZRL7-250 | 功能描述:模數轉換器 - ADC 12 Bit 250 Msps ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9635-125EBZ | 功能描述:BOARD EVAL FOR AD9635-125 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9635BCPZ-125 | 功能描述:IC ADC 12BIT SRL 125MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9635BCPZ-80 | 功能描述:IC ADC 12BIT SRL 80MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。