參數資料
型號： AD9516-3/PCBZ
廠商： Analog Devices Inc
文件頁數： 47/80頁
文件大小： 0K
描述： BOARD EVAL FOR AD9516-3 2.0GHZ
產品培訓模塊： Active Filter Design Tools
設計資源： AD9516 Eval Brd Schematic
AD9516 Gerber Files
AD9516-3 BOM
標準包裝： 1
主要目的： 計時，時鐘發生器
嵌入式： 否
已用 IC / 零件： AD9516-3
主要屬性： 2 輸入，14 輸出，2GHz VCO
次要屬性： CMOS、LVDS、LVPECL 輸出邏輯，ADIsimCLK&trade 圖形用戶界面
已供物品： 板，線纜，CD，電源
產品目錄頁面： 776 (CN2011-ZH PDF)
相關產品： AD9516-3BCPZ-ND - IC CLOCK PLL/VCO 2GHZ 64LFCSP
AD9516-3BCPZ-REEL7-ND - IC CLOCK PLL/VCO 2GHZ 64LFCSP
Data Sheet
AD9516-3
Rev. C | Page 51 of 80
Read
If the instruction word is for a read operation, the next N × 8
SCLK cycles clock out the data from the address specified in the
instruction word, where N is 1 to 3 as determined by [W1:W0].
If N = 4, the read operation is in streaming mode, continuing
until CS is raised. Streaming mode does not skip over reserved
or blank registers. The readback data is valid on the falling
edge of SCLK.
The default mode of the AD9516 serial control port is the
bidirectional mode. In bidirectional mode, both the sent data
and the readback data appear on the SDIO pin. It is also possible
to set the AD9516 to unidirectional mode via the SDO active bit
(Register 0x000[0] = 1b). In unidirectional mode, the readback
data appears on the SDO pin.
A readback request reads the data that is in the serial control
port buffer area, or the data that is in the active registers (see
Figure 63). Readback of the buffer or active registers is controlled
by Register 0x004[0].
The AD9516 supports only the long instruction mode, therefore
Register 0x000[4:3] must be set to 11b. (This register uses mirrored
bits). Long instruction mode is the default at power-up or reset.
The AD9516 uses Register Address 0x000 to Register
Address 0x232.
SCLK
SDIO
SDO
CS
SERIAL
CONTROL
PORT
BUF
F
E
R
RE
G
IS
T
E
RS
UPDATE
REGISTERS
WRITE REGISTER 0x232 = 0x01
TO UDATE REGISTERS
A
C
T
IVE
R
EG
IST
ER
S
06422-
037
Figure 63. Relationship Between Serial Control Port Buffer Registers and
Active Registers of the AD9516
THE INSTRUCTION WORD (16 BITS)
The MSB of the instruction word is R/W, which indicates
whether the instruction is a read or a write. The next two bits,
[W1:W0], indicate the length of the transfer in bytes. The final
13 bits are the address ([A12:A0]) at which to begin the read or
write operation.
For a write, the instruction word is followed by the number of
bytes of data indicated by Bits[W1:W0] (see Table 47).
Table 47. Byte Transfer Count
W1
W0
Bytes to Transfer
0
1
0
1
2
1
0
3
1
Streaming mode
The 13 bits found in [A12:A0] select the address within the
register map that is written to or read from during the data
transfer portion of the communications cycle. Only Bits[A9:A0]
are needed to cover the range of the 0x232 registers used by the
AD9516. Bits[A12:A10] must always be 0b. For multibyte
transfers, this address is the starting byte address. In MSB first
mode, subsequent bytes decrement the address.
MSB/LSB FIRST TRANSFERS
The AD9516 instruction word and byte data can be MSB first
or LSB first. Any data written to Register 0x000 must be mirrored;
the upper four bits (Bits[7:4]) with the lower four bits (Bits[3:0]).
This makes it irrelevant whether LSB first or MSB first is in
effect. As an example of this mirroring, see the default setting
for this register: 0x18, which mirrors Bit 4 and Bit 3. This sets
the long instruction mode (which is the default and the only
mode that is supported).
The default for the AD9516 is MSB first.
When LSB first is set by Register 0x000[1] and Register 0x000[6],
it takes effect immediately because it affects only the operation
of the serial control port and does not require that an update
be executed.
When MSB first mode is active, the instruction and data bytes
must be written from MSB to LSB. Multibyte data transfers in
MSB first format start with an instruction byte that includes the
register address of the most significant data byte. Subsequent
data bytes must follow, in order, from the high address to the
low address. In MSB first mode, the serial control port internal
address generator decrements for each data byte of the
multibyte transfer cycle.
When LSB first is active, the instruction and data bytes must be
written from LSB to MSB. Multibyte data transfers in LSB first
format start with an instruction byte that includes the register
address of the least significant data byte followed by multiple
data bytes. The internal byte address generator of the serial
control port increments for each byte of the multibyte
transfer cycle.
The AD9516 serial control port register address decrements from
the register address just written toward 0x000 for multibyte I/O
operations if the MSB first mode is active (default). If the LSB
first mode is active, the register address of the serial control port
increments from the address just written toward Address 0x232
for multibyte I/O operations.
Streaming mode always terminates when it hits Address 0x232.
Note that unused addresses are not skipped during multibyte
I/O operations.
Table 48. Streaming Mode (No Addresses Are Skipped)
Write Mode
Address Direction
Stop Sequence
LSB first
Increment
0x230, 0x231, 0x232, stop
MSB first
Decrement
0x001, 0x000, 0x232, stop
相關PDF資料
PDF描述
RSC06DRXH-S734 CONN EDGECARD 12POS DIP .100 SLD
1-1624112-4 INDUCTOR 2NH 5% 0402
AD9513/PCBZ BOARD EVAL FOR AD9513
AD9516-1/PCBZ BOARD EVALUATION FOR AD9516-1
MAX876AESA+T IC VREF SERIES PREC 10V 8-SOIC
相關代理商/技術參數
參數描述
AD9516-4 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Output Clock Generator with Integrated 1.6 GHz VCO
AD9516-4/PCBZ 功能描述:BOARD EVAL FOR AD9516-4 1.8GHZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
AD9516-4/PCBZ 制造商:Analog Devices 功能描述:AD9516-4, PLL CLOCK SYNTHESIZER, EVALUAT
AD9516-4BCPZ 功能描述:IC CLOCK GEN 1.6GHZ VCO 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
AD9516-4BCPZ 制造商:Analog Devices 功能描述:CLOCK GENERATOR, 1.8GHZ, LFCSP-64
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*