- 您現在的位置：買賣IC網 > PDF目錄1893 > AD8193ACPZ (Analog Devices Inc)IC SWITCH TMDS BUFF 2:1 32LFCSP PDF資料下載
參數資料
| 型號： | AD8193ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH TMDS BUFF 2:1 32LFCSP |
| 標準包裝： | 1 |
| 功能： | 開關 |
| 電路： | 1 x 2:1 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 托盤 |
AD8193
Rev. 0 | Page 10 of 16
OUTPUT CHANNELS
Each high speed output differential pair is terminated to the
3.3 V VTTO power supply through two single-ended 50 Ω
on-chip resistors, as shown in Figure 20. These matched on-
chip back-terminations absorb reflections on the output TMDS
channels and improve the overall system signal integrity. These
termination resistors are always present in the outputs and they
cannot be switched out.
OP[3:0]
ON[3:0]
AVEE
50
VTTO
50
IOUT
07
00
3-
0
21
Figure 20. High Speed Output Simplified Schematic
In a typical application, the AD8193 output is connected to the
input of an HDMI/DVI receiver, which provides a second set of
matched terminations in accordance with the HDMI 1.3
specification. If no receiver is connected, each of the AD8193
output pins should be tied to 3.3 V through a 50 Ω on-board
termination resistor.
SWITCHING MODE
The source selector pin, S_SEL, is used to select which of the
two input groups is routed to the output. Source A is selected
when S_SEL is pulled up to logic high, and Source B is selected
when S_SEL is pulled down to logic low. Logic levels for this pin
are set in accordance with the specifications listed in Table 5. The
AD8193 can be used as a single-link TMDS buffer by setting
S_SEL to one fixed logic value.
S_SEL also controls the switch status of the input termination
resistors. The termination resistors for the selected input are
always connected, whereas the termination resistors for the
unselected input are always switched out (high-Z inputs).
Table 5. S_SEL Description
S_SEL
Selected
Input
Input Termination Status
0
Input B
Input B terminations enabled, Input A
terminations disabled
1
Input A
Input A terminations enabled, Input B
terminations disabled
相關PDF資料 |
PDF描述 |
|---|---|
| AD8194ACPZ-R7 | IC SWITCH TMDS BUFF 2:1 32LFCSP |
| AD8195ACPZ | IC BUFF HDMI/DVI W/EQUAL 40LFCSP |
| AD8196ACPZ | IC SWITCH DVI/HDMI 2:1 56-LFCSP |
| AD8197AASTZ | IC HDMI/DVI SWITCH 4:1 100LQFP |
| AD8197ASTZ-RL | IC SWITCH DVI/HDMI 4:1 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8193ACPZ-R7 | 功能描述:IC SWITCH TMDS BUFF 2:1 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| AD8193-EVALZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Buffered 2:1 TMDS Switch |
| AD8194ACPZ | 功能描述:IC TMDS SWITCH BUFF 2:1 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| AD8194ACPZ-R7 | 功能描述:IC SWITCH TMDS BUFF 2:1 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| AD8194-EVALZ | 制造商:Analog Devices 功能描述:EVAL BD FOR AD8194 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。