參數資料
型號: AD8159ASVZ
廠商: Analog Devices Inc
文件頁數: 7/24頁
文件大?。?/td> 0K
描述: IC MUX/DEMUX QUAD BUFF 100TQFP
標準包裝: 1
系列: XStream™
應用: 2:1 多路復用器/1:2 多路分配器
接口: 串行
電源電壓: 3 V ~ 3.6 V
封裝/外殼: 100-TQFP 裸露焊盤
供應商設備封裝: 100-TQFP-EP(14x14)
包裝: 管件
安裝類型: 表面貼裝
產品目錄頁面: 801 (CN2011-ZH PDF)
AD8159
Rev. B | Page 15 of 24
THEORY OF OPERATION
The AD8159 relays received data on the demultiplexer Input Port
C to Output Port A and/or Output Port B, depending on the mode
selected by the BICAST control pin. On the multiplexer side,
the AD8159 relays received data on either Input Port A or Input
Port B to the Output Port C, based on the SEL[3:0] pin states.
The AD8159 is configured by toggling control pins. On the
demultiplexer side, when the device is configured in unicast
mode, it sends the received data on Input Port C to Output Port A
or Output Port B. When the device is configured in bicast mode,
received data on Input Port C is sent to both Output Port A and
Output Port B.
On the multiplexer side, only received data on Input Port A or
Input Port B is sent to Output Port C, depending on the state of the
SEL[3:0] pins. Table 4 summarizes port selection and configuration
when loopback is disabled (LB_A = LB_B = LB_C = 0).
When the device is in unicast mode, the output lanes on either
Port A or Port B are in an idle state. In the idle state, the output
tail current is set to 0 mA, and the P and N sides of the lane are
pulled up to the output termination voltage through the on-chip
termination resistors.
Table 4. Port Selection and Configuration Table
SELx
BICAST
OUT_A
OUT_B
OUT_C
0
IN_C
Idle
IN_A
0
1
IN_C
IN_A
1
0
Idle
IN_C
IN_B
1
IN_C
IN_B
INPUT EQUALIZATION (EQ) AND OUTPUT PRE-
EMPHASIS (PE)
In backplane applications, the AD8159 needs to compensate for
signal degradation over potentially long traces. The device supports
two levels of input equalization, configured on a per-port basis.
Table 5 summarizes the high frequency gain (EQ) for each control
setting, as well as the typical length of backplane trace that can
be compensated for each setting.
Table 5. Input Equalization Settings
EQ_x
EQ (dB)
Typical Backplane Length (Inches)
0
6
0 to 20
1
12
20 to 40+
The AD8159 also has four levels of output pre-emphasis,
configured for each port. The pre-emphasis circuitry adds a
controlled amount of overshoot to the output waveform to
compensate for the loss in a backplane trace.
Table 6 summarizes the high frequency gain, amount of over-
shoot, and the typical backplane channel length (including two
connectors) that can be compensated for using each setting.
A typical backplane is made of FR4 material with 8 mil wide
traces and 8 mil spacing, loosely coupled differential traces.
Each backplane channel consists of two connectors. The total
length of the channel includes 3 inches of traces on each card.
Table 6. Output Pre-Emphasis Settings
PE_x[1]
PE_x[0]
PE (dB)
Overshoot
Typical
Backplane
Length (Inches)
0
0%
0 to 10
0
1
1.9
15%
10 to 20
1
0
3.5
35%
20 to 30
1
4.9
60%
30 to 40+
相關PDF資料
PDF描述
AD8174ANZ IC MUX SW W/AMP 250MHZ 14-DIP
AD8175ABPZ IC CROSSPOINT SWITCH TRPL 676BGA
AD8176ABPZ IC VIDEO CROSSPOINT SWIT 676BGA
AD8177ABPZ IC VIDEO CROSSPOINT SWIT 676BGA
AD8178ABPZ IC VIDEO CROSSPOINT SWIT 676BGA
相關代理商/技術參數
參數描述
AD8159-EVAL-AC 制造商:Analog Devices 功能描述:EVAL KIT FOR AC-COUPLED EVAL BD - Bulk
AD8159-EVAL-DC 制造商:Analog Devices 功能描述:DC-COUPLED EVAL BD - Bulk
AD8159XSVZ 制造商:Analog Devices 功能描述:QUAD-LANE 3.2GBPS 2:1 MUX / 1:2 DEMUX SWITCH 100-PIN TQFP_EP - Trays
AD815ARB24 制造商:Analog Devices 功能描述:
AD815ARB-24 制造商:Rochester Electronics LLC 功能描述:SOIC HIGH OUTPUT CURRENT DIFF DRIVER - Bulk 制造商:Analog Devices 功能描述:Operational Amplifier IC Number of Ampli 制造商:Analog Devices Inc. 功能描述:High Output Current Differential Driver