- 您現在的位置：買賣IC網 > PDF目錄1985 > AD7986BCPZ-RL7 (Analog Devices Inc)IC ADC 18BIT 2MSPS SAR 20LFCSP PDF資料下載
參數資料
| 型號： | AD7986BCPZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT 2MSPS SAR 20LFCSP |
| 產品培訓模塊： | Motor Control |
| 標準包裝： | 1,500 |
| 位數： | 18 |
| 采樣率（每秒）： | 2M |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 34mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7986
Rev. B | Page 12 of 28
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 22).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Zero Error
Zero error is the difference between the ideal midscale voltage,
that is, 0 V, from the actual voltage producing the midscale
output code, that is, 0 LSB.
Gain Error
The first transition (from 100 ... 00 to 100 ... 01) should occur at
a level LSB above nominal negative full scale (4.095984 V
for the ±4.096 V range). The last transition (from 011 … 10 to
011 … 11) should occur for an analog voltage 1 LSB below
the nominal full scale (+4.095953 V for the ±5 V range). The
gain error is the deviation of the difference between the actual
level of the last transition and the actual level of the first
transition from the difference between the ideal levels.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD as follows:
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Noise-Free Code Resolution
Noise-free code resolution is the number of bits beyond which it is
impossible to distinctly resolve individual codes. It is calculated as
Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise)
and is expressed in bits.
Effective Resolution
Effective resolution is calculated as
Effective Resolution = log2(2N/RMS Input Noise)
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in decibels. It is
measured with a signal at 60 dBF so that it includes all noise
sources and DNL artifacts.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-(Noise + Distortion) (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components that are less than
the Nyquist frequency, including harmonics but excluding dc.
The value of SINAD is expressed in decibels.
Aperture Delay
Aperture delay is the measure of the acquisition performance
and is the time between the rising edge of the CNV input and
when the input signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7988-1BRMZ-RL7 | IC ADC 16BIT SRL 100KSPS 10MSOP |
| AD7991YRJZ-1RL | IC ADC 12BIT 4CH I2C SOT23-8 |
| AD7992BRMZ-1REEL | IC ADC 12BIT 2CHAN I2C 10MSOP |
| AD7994BRUZ-1 | IC ADC 12BIT 4CHAN I2C 16TSSOP |
| AD800-52BR | IC CLK\DATA RECOVERY PLL 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7986BCPZ-U1 | 制造商:Analog Devices 功能描述:16-BIT, 10MSPS PULSAR DIFFERENTIAL ADC - Rail/Tube |
| AD7986XCPZ-U1 | 制造商:Analog Devices 功能描述:16-BIT, 10MSPS PULSAR DIFFERENTIAL ADC - Rail/Tube |
| AD7988-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| AD7988-1_1208 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power PulSAR ADCs in MSOP/LFCSP (QFN) |
| AD7988-1BCPZ | 制造商:Analog Devices 功能描述:ADC 100KSPS 16BIT SPI 10LFCSP 制造商:Analog Devices 功能描述:ADC, 100KSPS, 16BIT, SPI, 10LFCSP 制造商:Analog Devices 功能描述:ADC, 100KSPS, 16BIT, SPI, 10LFCSP, Resolution (Bits):16bit, Sampling Rate:100kSP 制造商:Analog Devices 功能描述:ADC, 100KSPS, 16BIT, SPI, 10LFCSP, Resolution (Bits):16bit, Sampling Rate:100kSPS, Digital IC Case Style:QFN, No. of Pins:10, Input Channel Type:Pseudo Differential, Data Interface:Microwire, QSPI, SPI, Operating Temperature , RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。