參數資料
型號： AD7682
廠商： Analog Devices, Inc.
英文描述： 16-Bit, 8-Channel, 250 kSPS PulSAR㈢ ADC.
中文描述： 16位，8通道，250 kSPS的PulSAR系列㈢ADC的。
文件頁數： 16/20頁
文件大?。?/td> 2041K
代理商： AD7682
AD7689
Preliminary Technical Data
Regardless, there is no need for an additional lower value
ceramic decoupling capacitor (for example, 100 nF) between the
REF and GND pins.
For applications that use multiple AD7689s or other PulSAR
devices, it is more effective to use the internal reference buffer
to buffer the external reference voltage thus reducing SAR
conversion crosstalk.
The voltage reference temperature coefficient (TC) directly impacts
full scale; therefore, in applications where full-scale accuracy
matters, care must be taken with the TC. For instance, a
±15 ppm/°C TC of the reference changes full-scale by ±1 LSB/°C.
POWER SUPPLY
The AD7689 uses three power supply pins: two core supplies,
VDD, and a digital input/output interface supply, VIO. VIO
allows direct interface with any logic between 1.8 V and VDD.
To reduce the supplies needed, the VIO and VDD pins can be
tied together. The AD7689 is independent of power supply
sequencing between VIO and VDD. Additionally, it is very
insensitive to power supply variations over a wide frequency
range.
The AD7689 powers down automatically at the end of each
conversion phase; therefore, the operating currents and power
scale linearly with the sampling rate. This makes the part ideal
for low sampling rates (even of a few hertz) and low battery-
powered applications.
SUPPLYING THE ADC FROM THE REFERENCE
For simplified applications, the AD7689, with its low operating
current, can be supplied directly using the reference circuit
shown in Figure 16. The reference line can be driven by
The system power supply directly
A reference voltage with enough current output capability,
such as the
ADR43x/ADR44x
A reference buffer, such as the
AD8031
, which can also
filter the system power supply, as shown in Figure 16
Rev. PrC | Page 16 of 20
AD8031
AD7689
VIO
CAP
VDD
22μF
1μF
10
10k
5V
5V
5V
1μF
1
1
OPTIONAL REFERENCE BUFFER AND FILTER.
Figure 16. Example of an Application Circuit
-
DIGITAL INTERFACE
The AD7689, uses a simple 4-wire interface and is compatible
with SPI, QSPI, digital hosts, and DSPs, for example, Blackfin
ADSP-BF53x or ADSP-219x.
The interface uses the CNV, DIN, SCK, and SDO signals and
allows CNV, which initiates the conversions, to be independent
of the read back timing. This is useful in low jitter sampling or
simultaneous sampling applications.
CFG Writing
Prior to conversion, the AD7689 needs the CFG written to
unless the factory default setting is to be used as described in
the beginning of the Configuration Register section. If DIN is
high during the 1
st
SCK falling edge, CFG will be updated on
the 14
th
falling SCK edge. After the 14
th
SCK, the CFG will be
disabled and not accept any new CFG data until after the end of
conversion, t
CONV
(max). The CFG must be updated before the
end of conversion for the setting to take effect for the next
conversion. It can also be updated while reading back data thus
minimizing the SCK activity.
Conversion Data
The conversion data can be read at any time; during acquisition,
during conversion and after conversion. While reading during
conversion, the data read is from the previous conversion (
n-1
)
as the current conversion (
n
) is active.
The AD7689 offers the flexibility to optionally force a start bit
in front of the data bits. This start bit can be used as a BUSY
signal indicator to interrupt the digital host and trigger the data
reading. Otherwise, without a BUSY indicator, the user must
time out the maximum conversion time prior to readback. The
BUSY indicator feature is enabled when the CNV is held low
before the maximum conversion time, t
CONV
(max).
Note that in the following sections, the timing diagrams
indicate digital activity (SCK, CNV, DIN) during the
conversion. However, due to the possibility of performance
degradation, digital activity should only occur prior to the
minimum conversion time, t
CONV
(min) since the AD7689
provides error correction circuitry that can correct for an
incorrect bit during this time. The user should configure the
AD7689 and initiate the busy indicator (if desired) during this
time. It is also possible to corrupt the sample by having SCK or
DIN transitions near the sampling instant. Therefore, it is
recommended to keep the digital pins quiet for approximately
30 ns before and 10 ns after the rising edge of CNV. To this
extent, it is recommended, to use a discontinuous SCK whenever
possible to avoid any potential performance degradation.
相關PDF資料
PDF描述
AD7689 16-Bit, 8-Channel, 250 kSPS PulSAR㈢ ADC.
AD7699 16-Bit, 8-Channel, 250 kSPS PulSAR㈢ ADC.
ADA4851-4 Low Cost, High Speed, Rail-to-Rail, Output Op Amps
ADA4851-2 Low Cost, High Speed, Rail-to-Rail, Output Op Amps
ADA4899-1 Unity Gain Stable, Ultralow Distortion, 1 nV/ Hz Voltage Noise, High Speed Op Amp
相關代理商/技術參數
參數描述
AD7682BCBZ-RL7 功能描述:16 Bit Analog to Digital Converter 4 Input 1 SAR 20-WLCSP (2.39x2.39) 制造商:analog devices inc. 系列:PulSAR? 包裝:帶卷（TR） 零件狀態:有效 位數:16 采樣率（每秒）:250k 輸入數:4 輸入類型:差分，單端 數據接口:SPI，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:2.3 V ~ 5.5 V 電壓 - 電源，數字:* 特性:溫度傳感器 工作溫度:-40°C ~ 85°C 封裝/外殼:20-UFBGA，WLCSP 供應商器件封裝:20-WLCSP（2.39x2.39） 標準包裝:1,500
AD7682BCPZ 功能描述:IC ADC 16BIT 4CH 250KSPS 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7682BCPZRL7 功能描述:IC ADC 16BIT 4CH 250KSPS 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7683 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN
AD7683ACPZRL 功能描述:IC ADC 16BIT SRL 100KSPS 8LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*