- 您現在的位置：買賣IC網 > PDF目錄10244 > AD7661ASTZRL (Analog Devices Inc)IC ADC 16BIT W/REF 48LQFP PDF資料下載
參數資料
| 型號： | AD7661ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT W/REF 48LQFP |
| 標準包裝： | 2,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 25mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個偽差分，單極 |
| 配用： | EVAL-AD7661CBZ-ND - BOARD EVALUATION FOR AD7661 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7661
Rev. 0 | Page 19 of 28
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7661. The noise
coming from the driver is filtered by the AD7661 analog
input circuit 1-pole low-pass filter made by R1 and C2 or
by the external filter, if one is used. The SNR degradation
due to the amplifier is
π
+
=
2
3
)
(
2
784
28
log
20
N
dB
LOSS
Ne
f
SNR
where:
f–3dB is the input bandwidth, in MHz, of the AD7661 (0.82)
or the cutoff frequency of the input filter, if one is
used.
N
is the noise factor of the amplifier (+1 in buffer
configuration).
eN
is the equivalent input noise voltage of the op amp, in
nV/√Hz.
For example, the OP184 driver, which has an equivalent
input noise of 4 nV/√Hz and a noise gain of +1 when
configured as a buffer, degrades the SNR by only 0.11 dB.
The driver needs to have a THD performance suitable to
that of the AD7661. Figure 15 gives the THD versus
frequency that the driver should exceed.
usually appropriate for almost all applications. As an alternative,
in very high speed and noise-sensitive applications, the AD8021
with an external 10 pF compensation capacitor can be used.
This capacitor should have good linearity as an NPO ceramic or
mica type. Moreover, the use of a noninverting +1 gain
arrangement is recommended and helps to obtain the best
signal-to-noise ratio.
The AD8022 could also be used if a dual version is needed
and gain of +1 is present. The AD829 is an alternative in
applications where high frequency (above 100 kHz)
performance is not required. In gain of +1 applications, it
requires an 82 pF compensation capacitor. The AD8610 is
an option when low bias current is needed in low
frequency applications.
Voltage Reference Input
The AD7661 allows the choice of either a very low temperature
drift internal voltage reference or an external 2.5 V reference.
Unlike many ADCs with internal references, the internal
reference of the AD7661 provides excellent performance and
can be used in almost all applications.
To use the internal reference along with the internal buffer,
PDREF and PDBUF should both be LOW. This will produce
1.2 V on REFBUFIN which, amplified by the buffer, will result
in a 2.5 V reference on the REF pin.
The output impedance of REFBUFIN is 11 k (minimum) when
the internal reference is enabled. It is necessary to
decouple
REFBUFIN with a ceramic capacitor greater than 10 nF. Thus
the capacitor provides an RC filter for noise reduction.
To use an external reference along with the internal buffer,
PDREF should be HIGH and PDBUF should be LOW. This
powers down the internal reference and allows the 2.5 V
reference to be applied to REFBUFIN.
To use an external reference directly on REF pin, PDREF and
PDBUF should both be HIGH.
PDREF and PDBUF power down the internal reference and the
internal reference buffer, respectively. Note that the PDREF and
PDBUF input current should never exceed 20 mA. This could
eventually occur when input voltage is above AVDD (for
instance at power up). In this case, a 100 series resistor is
recommended.
The internal reference is temperature compensated to 2.5 V ±
20 mV. The reference is trimmed to provide a typical drift of
3 ppm/°C . This typical drift characteristic is shown in Figure
22. For improved drift performance, an external reference, such
as the AD780, can be used.
The AD7661 voltage reference input REF has a dynamic input
impedance; it should therefore be driven by a low impedance
source with efficient decoupling between the REF and
REFGND inputs. This decoupling depends on the choice of the
voltage reference but usually consists of a low ESR tantalum
capacitor connected to REF and REFGND with minimum
parasitic inductance. A 10 F (X5R, 1206 size) ceramic chip
capacitor (or 47 F tantalum capacitor) is appropriate when
using either the internal reference or one of these
recommended reference voltages:
The low power ADR291
The low cost AD1582
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2391CLX-16#PBF | IC ADC 16BIT SER/PAR 250K 48LQFP |
| NE570DG | IC COMPANDOR DUAL GAIN 16-SOIC |
| MS27473E10A35PB | CONN PLUG 13POS STRAIGHT W/PINS |
| LTC2391CUK-16#PBF | IC ADC 16BIT SER/PAR 250K 48QFN |
| LTC1418IG#TR | IC A/D CONV 14BIT SRL&PAR 28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7663 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit 1 MSPS SAR Unipolar ADC with Ref |
| AD7663ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 16-bit Parallel/Serial 48-Pin LFCSP EP |
| AD7663ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R |
| AD7663ACPZ | 功能描述:IC ADC 16BIT CMOS 5V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7663ACPZRL | 功能描述:IC ADC 16BIT CMOS 5V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。