參數資料
型號： AD7606BSTZ
廠商： Analog Devices Inc
文件頁數： 6/36頁
文件大?。?/td> 0K
描述： IC DAS W/ADC 16BIT 8CH 64LQFP
設計資源： Layout Considerations for an Expandable Multichannel Simultaneous Sampling Data Acquisition System Based on AD7606 (CN0148)
標準包裝： 1
類型： 數據采集系統（DAS），ADC
分辨率（位）： 16 b
采樣率（每秒）： 200k
數據接口： DSP，MICROWIRE?，并聯，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 2.3 V ~ 5.25 V，4.75 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
AD7606/AD7606-6/AD7606-4
Data Sheet
Rev. C | Page 14 of 36
Pin No.
Type1
Mnemonic
Description
AD7606
AD7606-6
AD7606-4
8
DI
RANGE
Analog Input Range Selection. Logic input. The polarity on this pin deter-
mines the input range of the analog input channels. If this pin is tied to a
logic high, the analog input range is ±10 V for all channels. If this pin is tied to
a logic low, the analog input range is ±5 V for all channels. A logic change
on this pin has an immediate effect on the analog input range. Changing
this pin during a conversion is not recommended for fast throughput rate
applications. See the Analog Input section for more information.
9, 10
DI
CONVST A,
CONVST B
CONVST A,
CONVST B
CONVST A,
CONVST B
Conversion Start Input A, Conversion Start Input B. Logic inputs. These
logic inputs are used to initiate conversions on the analog input channels.
For simultaneous sampling of all input channels, CONVST A and CONVST B
can be shorted together, and a single convert start signal can be applied.
Alternatively, CONVST A can be used to initiate simultaneous sampling: V1,
V2, V3, and V4 for the AD7606; V1, V2, and V3 for the AD7606-6; and V1
and V2 for the AD7606-4. CONVST B can be used to initiate simultaneous
sampling on the other analog inputs: V5, V6, V7, and V8 for the AD7606;
V4, V5, and V6 for the AD7606-6; and V3 and V4 for the AD7606-4. This is
possible only when oversampling is not switched on. When the CONVST A or
CONVST B pin transitions from low to high, the front-end track-and-hold
circuitry for the respective analog inputs is set to hold.
11
DI
RESET
Reset Input. When set to logic high, the rising edge of RESET resets the
AD7606/AD7606-6/AD7606-4. The part should receive a RESET pulse after
power-up. The RESET high pulse should typically be 50 ns wide. If a RESET
pulse is applied during a conversion, the conversion is aborted. If a RESET
pulse is applied during a read, the contents of the output registers reset
to all zeros.
12
DI
RD/SCLK
Parallel Data Read Control Input When the Parallel Interface Is Selected (RD)/
Serial Clock Input When the Serial Interface Is Selected (SCLK). When both
CS and RD are logic low in parallel mode, the output bus is enabled.
In serial mode, this pin acts as the serial clock input for data transfers.
The CS falling edge takes the DOUTA and DOUTB data output lines out
of three-state and clocks out the MSB of the conversion result. The rising
edge of SCLK clocks all subsequent data bits onto the DOUTA and DOUTB
serial data outputs. For more information, see the Conversion Control
section.
13
DI
CS
Chip Select. This active low logic input frames the data transfer. When
both CS and RD are logic low in parallel mode, the DB[15:0] output bus is
enabled and the conversion result is output on the parallel data bus lines.
In serial mode, CS is used to frame the serial read transfer and clock out
the MSB of the serial output data.
14
DO
BUSY
Busy Output. This pin transitions to a logic high after both CONVST A and
CONVST B rising edges and indicates that the conversion process has started.
The BUSY output remains high until the conversion process for all channels
is complete. The falling edge of BUSY signals that the conversion data is
being latched into the output data registers and is available to read after
a Time t4. Any data read while BUSY is high must be completed before the
falling edge of BUSY occurs. Rising edges on CONVST A or CONVST B have
no effect while the BUSY signal is high.
15
DO
FRSTDATA
Digital Output. The FRSTDATA output signal indicates when the first channel,
V1, is being read back on the parallel, byte, or serial interface. When the
CS input is high, the FRSTDATA output pin is in three-state. The falling
edge of CS takes FRSTDATA out of three-state. In parallel mode, the falling
edge of RD corresponding to the result of V1 then sets the FRSTDATA pin
high, indicating that the result from V1 is available on the output data bus.
The FRSTDATA output returns to a logic low following the next falling edge
of RD. In serial mode, FRSTDATA goes high on the falling edge of CS because
this clocks out the MSB of V1 on DOUTA. It returns low on the 16th SCLK
falling edge after the CS falling edge. See the Conversion Control section
for more details.
相關PDF資料
PDF描述
AD7607BSTZ-RL IC DAS W/ADC 14BIT 8CH 64LQFP
AD7608BSTZ-RL IC DAS W/ADC 18BIT 8CH 64LQFP
AD7609BSTZ-RL IC DAS W/ADC 18BIT 8CH 64LQFP
AD760AQ IC DAC 16BIT W/AMP SRL 28-CDIP
AD766AN IC DAC 16BIT W/REF DSP 16-DIP
相關代理商/技術參數
參數描述
AD7606BSTZ 制造商:Analog Devices 功能描述:IC ADC 16BIT 200KSPS QFP-64 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64
AD7606BSTZ-4 功能描述:IC DAS W/ADC 16BIT 4CH 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1
AD7606BSTZ-4 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64
AD7606BSTZ-4RL 功能描述:IC DAS W/ADC 16BIT 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤
AD7606BSTZ-6 功能描述:IC DAS W/ADC 16BIT 6CH 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*