- 您現在的位置：買賣IC網 > PDF目錄1981 > AD7484BSTZ (Analog Devices Inc)IC ADC 14BIT SAR 3MSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD7484BSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/20頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SAR 3MSPS 48-LQFP |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 3M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 90mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個單端，單極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7484CBZ-ND - BOARD EVALUATION FOR AD7484 |
AD7484
Rev. C | Page 11 of 20
TERMINOLOGY
Integral Nonlinearity
The integral nonlinearity is the maximum deviation from a
straight line passing through the endpoints of the ADC transfer
function. The endpoints of the transfer function are zero scale, a
point 1/2 LSB below the first code transition, and full scale, a
point 1/2 LSB above the last code transition.
Differential Nonlinearity
The differential nonlinearity is the difference between the
measured and ideal 1 LSB change between any two adjacent
codes in the ADC.
Offset Error
The offset error is the deviation of the first code transition
(00…000) to (00…001) from the ideal, that is, AGND + 0.5 LSB.
Gain Error
The gain error is the deviation of the last code transition
(111…110) to (111…111) from the ideal, that is, VREF 1.5 LSB,
after the offset error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold acquisition time is the time required for the
output of the track-and-hold amplifier to reach its final value,
within ±1/2 LSB, after the end of conversion (the point at which
the track-and-hold returns to track mode).
Signal-to-Noise + Distortion (SINAD) Ratio
The SINAD ratio is the measured ratio of signal-to-noise +
distortion at the output of the ADC. The signal is the rms ampli-
tude of the fundamental. Noise is the sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc. The
ratio is dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the quantization
noise. The theoretical SINAD ratio for an ideal N-bit converter
with a sine wave input is given by
Signal-to-Noise + Distortion = (6.02N + 1.76)dB
Therefore, this is 86.04 dB for a 14-bit converter.
Total Harmonic Distortion (THD)
The THD is the ratio of the rms sum of the harmonics to the
fundamental. It is defined as
( )
1
2
6
2
5
2
4
2
3
2
V
THD
+
=
log
20
dB
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
The peak harmonic or spurious noise is the ratio of the rms
value of the next largest component in the ADC output spectrum
(up to fS/2 and excluding dc) to the rms value of the fundamental.
The value of this specification is usually determined by the
largest harmonic in the spectrum, but for ADCs where the
harmonics are buried in the noise floor, it is a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m and n = 0, 1, 2, 3, and so on. Intermodulation distortion
terms are those for which neither m nor n is equal to zero. For
example, the second order terms include (fa + fb) and (fa fb),
whereas the third order terms include (2fa + fb), (2fa fb), (fa +
2fb), and (fa 2fb).
The AD7484 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second order terms are usually distanced in
frequency from the original sine waves, whereas the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second order and third order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7485BSTZ | IC ADC 14BIT SAR 1MSPS 48-LQFP |
| AD7490BRU-REEL | IC ADC 12BIT 16CH 28-TSSOP T/R |
| AD7492ARZ-5 | IC ADC 12BIT REF/CLOCK 24SOIC |
| AD7495BRM | IC ADC 12BIT SRL LP W/REF 8MSOP |
| AD75004KP | IC DAC 12BIT QUAD W/BUFF 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7484BSTZ | 制造商:Analog Devices 功能描述:IC 14-BIT ADC |
| AD7485 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1 MSPS, Serial 14-Bit SAR ADC |
| AD7485BST | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 14-bit Serial 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:14 BIT, 1MSPS, SERIAL ADC I.C. - Tape and Reel 制造商:Analog Devices 功能描述:14BIT SERIAL ADC SMD 7485 LQFP48 |
| AD7485BSTZ | 功能描述:IC ADC 14BIT SAR 1MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7490 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 1 MSPS, 12-Bit ADC with Sequencer in 28-Lead TSSOP |
發布緊急采購，3分鐘左右您將得到回復。