The AD7152/AD7153 support an I2C-" />
參數資料
型號: AD7152BRMZ
廠商: Analog Devices Inc
文件頁數: 3/24頁
文件大小: 0K
描述: IC CDC 12BIT 2/4CH 10MSOP
特色產品: AD715x Series Capacitance-to-Digital Converters & Evaluation Board
標準包裝: 50
類型: 電容數字轉換器
分辨率(位): 12 b
數據接口: 串行
電壓電源: 單電源
電源電壓: 2.7 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
產品目錄頁面: 781 (CN2011-ZH PDF)
配用: EVAL-AD7152EBZ-ND - BOARD EVAL AD7152
AD7152/AD7153
Rev. 0 | Page 11 of 24
SERIAL INTERFACE
The AD7152/AD7153 support an I2C-compatible, 2-wire serial
interface. The two wires on the I2C bus are called SCL (clock)
and SDA (data). These two wires carry all addressing, control,
and data information one bit at a time over the bus to all connected
peripheral devices. The SDA wire carries the data, while the
SCL wire synchronizes the sender and receiver during the
data transfer. I2C devices are classified as either master or slave
devices. A device that initiates a data transfer message is called a
master; a device that responds to this message is called a slave.
To control the AD7152/AD7153 via the bus, the following
protocol must be followed. The master initiates a data transfer
by establishing a start condition, defined by a high-to-low
transition on SDA while SCL remains high. This indicates that
the start byte follows. This 8-bit start byte is made up of a 7-bit
address plus an R/W bit indicator.
All peripherals connected to the bus respond to the start
condition and shift in the next 8 bits (7-bit address and an
R/W bit). The bits arrive MSB first. The peripheral that
recognizes the transmitted address responds by pulling the
data line low during the ninth clock pulse. This is known as the
acknowledge bit. All other devices withdraw from the bus at
this point and maintain an idle condition. An exception to this
is the general call address, which is described in the General
Call section. The idle condition is where the device monitors
the SDA and SCL lines waiting for the start condition and the
correct address byte. The R/W bit determines the direction of
the data transfer. A Logic 0 LSB in the start byte means that the
master writes information to the addressed peripheral. In this
case, the device becomes a slave receiver. A Logic 1 LSB in the
start byte means that the master reads information from the
addressed peripheral. In this case, the device becomes a slave
transmitter. In all instances, the AD7152/AD7153 act as a
standard slave device on the I2C bus.
The start byte address is Address 0x90 for a write and Address
0x91 for a read.
WRITE OPERATION
When a write is selected, the byte following the start byte is
always the register address pointer (subaddress) byte, which
points to one of the internal registers on the AD7152/AD7153.
The address pointer byte is automatically loaded into the
address pointer register and acknowledged by the AD7152/
AD7153. After the address pointer byte acknowledge, a stop
condition, a repeated start condition, or another data byte can
follow from the master.
A stop condition is defined by a low-to-high transition on SDA
while SCL remains high. If a stop condition is ever encountered
by the AD7152/AD7153, it returns to its idle condition and the
address pointer is reset to Address 0x00.
If a data byte is transmitted after the register address pointer
byte, the AD7152/AD7153 load this byte into the register that
is currently addressed by the address pointer register. The parts
send an acknowledge and the address pointer autoincrementer
automatically increments the address pointer register to the
next internal register address. Thus, subsequent transmitted
data bytes are loaded into sequentially incremented addresses.
If a repeated start condition is encountered after the address
pointer byte, all peripherals connected to the bus respond
exactly as previously outlined for a start condition, that is, a
repeated start condition is treated the same as a start condition.
When a master device issues a stop condition, it relinquishes
control of the bus, allowing another master device to take
control. Hence, a master wanting to retain control of the bus
issues successive start conditions known as repeated start
conditions.
READ OPERATION
When a read is selected in the start byte, the register that is
currently addressed by the address pointer is transmitted onto
the SDA line by the AD7152/AD7153. The regulator is then
clocked out by the master device, and the AD7152/AD7153
await an acknowledge from the master.
If an acknowledge is received from the master, the address
autoincrementer automatically increments the address pointer
register and outputs the next addressed register content onto
the SDA line for transmission to the master. If no acknowledge
is received, the AD7152/AD7153 return to the idle state and the
address pointer is not incremented.
The autoincrementer of the address pointers allows block data
to be written or read from the starting address and subsequent
incremental addresses.
In continuous conversion mode, autoincrementer of the address
pointers should be used for reading a conversion result; that is,
the three data bytes should be read using one multibyte read
transaction rather than three separate single-byte transactions.
The single-byte data read transaction may result in the data
bytes from two different results being mixed.
相關PDF資料
PDF描述
D38999/24WD5SC CONN RCPT 5POS JAM NUT W/SCKT
MS3122E18-11PW CONN RCPT 11POS BOX MNT W/PINS
D38999/24WJ90SB CONN RCPT 46POS JAM NUT W/SCKT
IDT728985JG IC DGTL SW 256X256 44-PLCC
M83723/85R1407N CONN RCPT 7POS JAM NUT W/PINS
相關代理商/技術參數
參數描述
AD7152BRMZ-REEL 功能描述:IC CDC 12BIT 2/4CH 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(tǒng)(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7153 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit Capacitance-to-Digital Converter
AD7153BRMZ 功能描述:IC CDC 12BIT 1/2CH 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(tǒng)(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7153BRMZ-REEL 功能描述:IC CDC 12BIT 1/2CH 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(tǒng)(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7156 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Power, 1.8 V, 3 mm × 3 mm, 2-Channel Capacitance Converter